Rowenta Steamforce Pro DW9510 handleiding

Niet gecategoriseerd

Rowenta

26 pagina's

PDF beschikbaar

Handleiding

6 7

PROBLEMS

Problem Cause Solution

The iron is plugged in, but the

soleplate of the iron remains

cold.

No mains supply. Check that the mains plug

is properly inserted or try

plugging the iron into a

different socket.

The automatic electronic auto

off is active.

Move your iron.

None or too little steam is

being emitted.

The iron is not ready to use. Wait until the mode you have

selected stops blinking.

NB: on "Nylon" mode, the

steam output is low to

preserve your clothes.

Not enough water in the

water tank.

Fill the water tank.

Anti-Drip is active

Wait for the soleplate to reach

the correct temperature.

The trigger is not pressed.

Press the trigger to get steam

output.

The steam is blocked on

NYLON mode in order to

protect your clothes

Select a higher mode if

needed

Brown streaks come through

the holes in the soleplate and

stain the fabric.

Residues in the steam

chamber or on the soleplate.

Use the Calc Clean Program

then clean your iron.

Do not add any descaling

agents, perfumed, or

scented additives to the

water in the water tank.

Use the Calc Clean Program

and clean your iron if you

have used the above.

Fabric fibres have

accumulated in the holes of

the soleplate and are burning.

Clean the soleplate with a

non-metallic sponge.

Your linen is not rinsed

sufficiently or you have

ironed a new garment before

washing it.

Ensure linen is rinsed

thoroughly.

Use of starch. Always spray starch onto the

reverse side of the fabric to

be ironed and clean your iron

soleplate afterwards.

Pure distilled /demineralised

or softened water is being

used.

Only use untreated tap water

or mix half tap water with half

distilled/demineralised water.

Use the Calc Clean Program

and clean your iron.

Iron is leaking.

Overuse of shot of steam

trigger.

Allow more time between

each shot.

Use of the shot of steam

trigger on NYLON, SILK or

WOOL modes.

Use only the steam boost on

COTTON and LINEN modes.

Use of chemical

descaling agents,

perfumed or scented

additives.

AFTER USE

8 • Emptying

Unplug the iron ﬁg 1. Pour away remaining water ﬁg 10.

9 • Storing

Allow the appliance to cool down for 1 hour before winding the cord around the heel. Store

the iron on its base in a dry and safe place

ﬁg 12.

IMPORTANT Do not wind the cord around the hot soleplate. Never store your iron

placed down on the soleplate.

Remove the plug from the wall socket and let the iron cool down before

maintenance and cleaning.

IMPORTANT: this program will last 4 to 6 minutes.

10 • Cleaning the iron

When the appliance has cooled down, wipe the iron down with a damp cloth or sponge. A non

abrasive cleaning agent can be used.

IMPORTANT Do not use sharp or abrasive cleaning agents or objects to clean the

soleplate and other parts of the iron.

WARNING : Do not use descaling agents even if advertised for steam irons. They will

permanently damage your iron.

MAINTENANCE AND CLEANING

11 • Calc clean program (4-6 min)

The Calc Clean System flushes dirt and scale particles out of the steam chamber.

This considerably prolongs the operational life of your iron.

Your iron needs to be cleaned when the CALC CLEAN warning light remains lighted on the

LED screen

ﬁg 11a.

If the "CALC CLEAN" light starts flashing when you are ironing, you can finish your ironing

session. There is no risk for your clothes nor the appliance.

TO START THE CALC CLEAN PROGRAM:

1. Unplug the iron (

ﬁg 1)

2. Fill in the water tank

ﬁg 2 & 3

3. Plug the iron (ﬁg 4)

4. Put the iron over a sink or a basin

5. Press simultaneously the Mode button & the trigger for 3 secondes to start the Calc Clean

Program. (

ﬁg 11b)

The iron will start to heat up without producing steam. When arrived at the maximum

temperature, the water will start to run down

ﬁg 11c. During the process, the fabrics on the LED

screen will blink alternatively. Once the process finished, the iron will automatically shut off.

Allow the appliance to cool down and then wipe the iron down with a damp cloth or a sponge.

6 • Anti-Drip system

It prevents water dripping out of the soleplate when the temperature is too low.

7 • Auto Off function

• For your safety, the electronic system cuts off the power and the auto off indicator

light flashes ﬁg 9 when:

- The iron remains motionless for more than 8 minutes on its base

- The iron remains flat or on its side for more than 30 seconds

To restart the iron, just move it gently until the warning light stops flashing.

Bekijk gratis de handleiding van Rowenta Steamforce Pro DW9510, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.