Rowenta Duolab LV5030F6 handleiding
Handleiding
Je bekijkt pagina 27 van 98
5352
YOUR CREAM SPILLS AND SPREADS IN THE APPLIANCE:
• Check that the capsules have been inserted correctly in their cases.
• Check that the capsule tip has not been folded on insertion. Replace your capsules, ensuring that the tip does not
fold on insertion.
• Check that you have not pressed the exible parts of the dispenser when removing it from the appliance. Pull the
dispenser by holding onto the rigid upper part.
• Make sure you have properly put the two capsules in the dispenser before starting the mixing cycle.
THERE IS NO CREAM WHEN PRESSING THE DISPENSER
• Check that the capsules have been properly inserted, and that the cream has not spilled inside the appliance. Ensure
that the capsules are placed properly.
• Check that the capsule end has not been folded on insertion. Replace your capsules, ensuring that the tip does not
fold on insertion.
• Check that you have not pressed the exible parts of the holder when removing it from the appliance. Pull the holder
by holding onto the rigid upper part.
• Make sure you have properly put the two capsules in the dispenser before starting the kneading cycle.
THE KNEADING CYCLE DOES NOT START.
• The ON/OFF button is lit: this is normal, just press the button again to start the cycle
• Check that the product has enough battery to start the cycle. Your product is designed with a safety feature, meaning
that the cycle will not start if there is not enough battery to nish it: recharge the battery of your product (see
“precautions for use” section for further details).
• The ON/O button is ashing: Check that the dispenser has been properly inserted into its case. The product emits a
sound signal when the dispenser is correctly inserted.
• Check that your capsules have been inserted the right way round into the dispenser. Look at the insertion direction
indicated by the arrow printed on the capsule.
• If, the dispenser is still not detected, contact your nearest after-sales service
YOU FIND SOME TREATMENT UNDER YOUR APPLIANCE.
• Do not place the dispenser into the product with used capsules. The capsules are single use.
• For all other cases, refer to the two rst paragraphs of this section.
THE DISPENSER DOES NOT GO INSIDE ITS CASE.
• Check that you have properly removed the transport block from the dispenser upon rst use.
• Ensure that the dispenser has been correctly closed before insertion
• Check that your capsules have been inserted the right way round into dispenser. Look at the insertion direction
indicated by the arrow printed on the capsule..
YOU CANNOT REMOVE THE DISPENSER AT THE END OF THE CYCLE.
• Contact your nearest after-sales service.
ONE OF THE CAPSULES REMAINS IN THE DISPENSER WHEN REMOVING IT.
• Remove the remaining capsule using a suitable tool. Refer to the above section on the removal of capsules.
YOUR PRODUCT IS IN SAFE MODE REPETITIVE AUDIBLE SIGNAL AND RAPID FLASHING OF THE BASE.
• In case your appliance is in safety mode, apply the reset process: hold down the two buttons H and I for 5 seconds. If
the problem persists, contact an Authorised Service Centre.
• If your appliance goes into safety mode, do not use the capsules and the cosmetic in the dispenser: use new capsules
if you restart a new cycle.
WHEN INSERTING THE DISPENSER, THE “PADLOCK” BUTTON LIGHTS UP, AND IT IS NOT POSSIBLE TO START A CYCLE:
• You cannot perform a cycle shortly after a rst one. Wait for the “padlock” button to go o to restart a cycle.
3. BEFORE FIRST USE
4. CLEANING
5. INTERNATIONAL LIMITED GUARANTEE
6. IN CASE OF PROBLEM
• Do not use at temperatures below 15°C and above 35°C.
• When assembling the accessories, make sure you properly lock them into place in their
compartment.
• This appliance is intended for domestic use only.
• It cannot be used for professional purposes.
• The guarantee shall become null and void if the appliance is used incorrectly.
• Should you need any additional information, in case of problems or simply to seek
advice, please contact your Duolab customer care.
• Contact details of your Duolab customer care can be found at www.duolab.com
• Always disconnect the appliance once fully charged, before cleaning or in the event of
an operational issue.
• Do not clean with abrasive or corrosive products.
• Do not submerge it or run it under water, even to clean it
• Do not clean the product or the dispenser by running it under water.
• Clean the product with a damp cloth after use.
• Do not put the appliance in the dishwasher.
• Do not wet the adaptor.
Flashing battery indicator
You have enough battery for 1 treatment. Charge your treatment
formulator as soon as possible
Battery indicator ashes 3 times and then goes o.
Your treatment formulator is out of battery. Charge it.
A 5 minutes charge will allow you to carry out 1 treatment.
Battery indicator o Your treatment formulator is charged
If you drop your appliance and it does not work normally, do not use it and contact an
Authorized Service Centre.
Bekijk gratis de handleiding van Rowenta Duolab LV5030F6, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Rowenta |
| Model | Duolab LV5030F6 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5740 MB |
