Handleiding
Je bekijkt pagina 19 van 25
36
Regulating the minimum flame
After lighting the burners, turn the control knob to the minimum setting and then remo-
ve the knob (this can easily be removed by apply a gentle pressure).
Using a small «Terminal» type screwdriver the regulating screw can be adjusted as in
Fig. 8. Turning the screw clockwise reduces the gas flow, whilst turning it anticlockwise
increases the flow – Use this adjustment to obtain a flame of approximately 3 to 4 mm
in length and then replace the control knob.
If GPL (cylinder) gas is being used, turn the screw clockwise right to the end of the
travel of the by-pass.
Screws
regulating
Gas tap calibrating screws
(flat head slot type)
ATTENTION: When cleaning the hob, take care to replace the burners correctly,
this will ensure that the ignition point is not blocked.
GENERAL ADVICE
For the best results, the flat-bottomed pans size should match the gas burner size as
follows:
— Small 12 cm.
— Medium from 12 to 18 cm. — Large from 18 to 24 cm.
— Double ring from 24 to 28 cm.
— Fish from 26 to 28 cm.; Rectangular pan max 210x370 - min. 150x290 mm.
For smaller containers a reducer stand (supplied with some models) should be used
and the gas burner should be regulated so that the flame does not overlap the base
of the pan. The reducer stand is for use with the medium burner. Vessels with conca-
ve or convex base should not be used.
WARNING: If a burner is accidentally extinguehed, turn the knob to the off posi-
tion and do not attempt to re-ignite if for at least 1 minute.
To protect the glass lid from damage and in the interests of safety, the burners/plates
must be turned off and the burner/pan support/plate area must be cool before closing
the lid down.
Mijorose burner: the heat diffusing plate, to be used only on the rear right hand
burner, is designed to provided a particularly delicate cooking facility. When
this facility is not required, the burner can be used in the conventional way.
INSTRUCTIONS FOR USE
Using the gas Burner
To ignite the burners, place a lighted taper close to the burner, press in and turn the
control knob anti-clockwise.
If the burners have not been used for a couple of days, wait for a few seconds before
lighting the burner, this will allow any air present in the pipes to escape.
For appliances equipped with electronic ignition, simply press down and turn the con-
trol knob to the position marked with a star
★
.
After the burner ignites, turn the knob to the control setting required.
The ignition is by repetitive spark generation; in case the burner does not light at once,
keep the knob in the ignition position for a maximum of 5 seconds.
If the burner does not ignite in this time, switch off the control knob and repeat the ope-
ration again.
As a safety device, some models automatically cut off the gas supply if the flame is
accidently extinguished. In this case, push and rotate the control knob until the
★
posi-
tion and keep it held
down for approx 5-6 seconds.
The burner will then remain lit.
35
Fig. 8
MAINTENANCE AND CLEANING
Important Advice
Before cleaning the Hob, ensure the appliance has cooled down. Remove the plug from
the socket or (if connected directly) switch off the electricity supply.
When cleaning the enamelled, varnished or chrome sections, use warm soapy water
or a non caustic detergent. For stainless steel use an appropriate cleaning solution.
Hotplates should only be cleaned with a cotton cloth coated with vaseline or seed oil.
Never use abrasives, corrosive detergents, bleaching agents or acids. Avoid any acid
or alkaline substances (lemon, juice, vinegar etc.) on the enamelled, varnisched or stain-
less steel sections.
The burners can be cleaned with soapy water. To restore their original shine, use a
household stainless steel cleaner. After cleaning, dry the burners and replace.
It is important the Burners are replaced correctly.
This appliance must only be used for the purpose for which it is intended, domestic
cooking, and any other use will be considered improper and could therefore be danger-
ous. The Manufacturer will not be responisble for any damage or loss resulting from
improper use.
air
regul.
4mm
13 mm
2mm
6mm
15 mm
4 mm
Working
burner
large mijorose
double ring
medium
small
fish
large
Ø injector
1/100 mm
120
2x94
93
80
2x94
127
Ø injector
1/100 mm
80
2x65
61
54
2x65
84
Qn
kW
2,65
3,3
1,5
1,1
3,3
2,95
l/h
G20
252
314
143
105
314
281
g/h
G30
193
238
109
80
238
215
g/h
G31
189
236
107
79
236
211
Qn
kW
2,5
3,1
1,45
1,05
3,1
2,8
l/h
G25
277
343
161
116
343
310
Qmin.
kW
0,570
0,900
0,380
0,250
0,900 G30
1 G20/G25
0,570
air
regul.
4mm
13 mm
2mm
6mm
15 mm
4mm
air
regul.
2mm
0mm
5mm
4mm
0mm
2mm
G20 G30 G25 G31
G30/G31G20/G25 G20/G30/G31 G25
Quota «X» depending
on type of gas
Table of gas consumption 1W = 0,860 kcal/h
air
regul.
5mm
15 mm
7mm
6mm
15 mm
5mm
Bekijk gratis de handleiding van Rosieres GTS 76, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Rosieres |
| Model | GTS 76 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 3305 MB |
