Renkforce RF-6BDS-350 handleiding
Handleiding
Je bekijkt pagina 4 van 8
7 Operation
7.1 Initialize a new disk
Important:
– Back up important data before using this product to prevent data deletion, modication,
or loss caused by user operations.
A new SSD, must be initialized, partitioned, and formatted before use.
Refer to the documentation or support resources provided by your operating system for infor-
mation about how to do this.
7.2 PM mode (read and write data)
1. Insert up to 6 SSDs into the SSD slots (6) / (11) in a vertical direction.
2. Connect the Type-C port to a computer with the USB-C
®
cable. Switch the mode switch
(5) to PM mode.
3. Connect the DC IN port to the power supply using the supplied power adapter and power
cord. Switch the power switch (3) to turn it on.
Æ The computer will automatically detect and install the hard drive. It will appear under
“Computer” as a newly added hard drive. You can read from and write to it.
7.3 Clone mode (clone data from source SSD to target SSD)
Important:
– Data will be copied from the source SSD to the target SSD.
– All existing data on the target SSD will be lost.
– Always back up important data before cloning.
– Do not remove a drive or disconnect the power supply during cloning.
Notes:
– For clone mode, don’t connect to a PC.
– The capacity of the target SSD must be greater than or equal to that of the source SSD.
1. Insert your source SSD with data into the Source 0 slot (6), and your target SSD into the
Target 1(or 2/3/4/5) slot (11). Switch the mode switch (5) to clone mode.
2. Connect to the power supply, and switch the power switch (3) to turn it on.
Æ The corresponding SSD indicators will light up.
3. Press the clone button (7) twice quickly.
Æ The product beeps three times to signal the start of cloning, and the progress display
lights up and starts counting.
Æ After cloning is complete, 100% will appear in the progress display, and the product will
beep three times to signal completion.
4. Switch the power switch (3) to power off. Then remove the SSDs.
8 Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Disconnect the product from the power supply.
2. Clean the product with a dry, bre-free cloth.
9 Disposal
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
in our Conrad ofces
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set
up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.
10 Technical data
10.1 Power adapter
Input.............................................. 100 - 240 V/DC, 50/60 Hz, max. 2 A
Output ........................................... 12 V/DC 7 A
10.2 Product
Input.............................................. 12 V/DC, 7 A via USB-C
®
Interface ........................................ USB-C
®
Data transfer speed ...................... Up to 5 Gbps
System requirement ..................... Windows
®
, macOS, Linux
10.3 Supported SSD
Type .............................................. M.2 SATA (B+M-Key) SSD
Size ............................................... 2230/2240/2260/2280/22110 mm
Memory size ................................. Max. 8 TB
10.4 Other
Operating temperature ................. 0 to +70 °C
Operating humidity ....................... 10 – 80 % RH (non-condensing)
Storage temperature ..................... -10 to +80 °C
Storage humidity ........................... 8 – 90 % RH (non-condensing)
Material ......................................... Plastic (case)
Dimensions (W x H x D) ............... 163 x 41 x 125 mm
Weight .......................................... 690 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2025 by Conrad Electronic SE. *3347288_V1_0425_02_mxs_m_en_(2)
Bekijk gratis de handleiding van Renkforce RF-6BDS-350, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Renkforce |
| Model | RF-6BDS-350 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1636 MB |
