Radial Engineering Workhorse Cube handleiding
Handleiding
Je bekijkt pagina 6 van 16
Radial Engineering Ltd.
The Cube™ Power Rack
True to the Music
®
INTRODUCTION
The Cube is a three card-slot power frame designed for 500 series modules. Up to three
modules may be used at any one time. The Cube routes the modules to the XLR and ¼" TRS
connectors on the rear panel via a 15-pin card-edge receptacle. Radial modules and those
that have been designed by other manufacturers to take advantage of the Workhorse’s extra
features will enjoy the added functionality of the Omniport
™
.
CARD-SLOT 2CARD-SLOT 3 CARD-SLOT 1
INPUT
OMNIPORT
FEED
LINK
12
INPUT
FEED
OFF
OFF
CARD SLOT 1CARD SLOT 2
OMNIPORT
OFF
OUTPUT OUTPUT
LINK
OFF
OUTPUT
INPUT
OUTPUT
INPUT
3
INPUT
CARD SLOT 3
OMNIPORT
OUTPUT
OUTPUT
INPUT
INPUT
OMNIPORT
FEED
LINK
12
INPUT
FEED
OFF
OFF
CARD SLOT 1CARD SLOT 2
OMNIPORT
OFF
OUTPUT OUTPUT
LINK
OFF
OUTPUT
INPUT
OUTPUT
INPUT
3
INPUT
CARD SLOT 3
OMNIPORT
OUTPUT
OUTPUT
INPUT
INPUT
OMNIPORT
FEED
LINK
12
INPUT
FEED
OFF
OFF
CARD SLOT 1CARD SLOT 2
OMNIPORT
OFF
OUTPUT OUTPUT
LINK
OFF
OUTPUT
INPUT
OUTPUT
INPUT
3
INPUT
CARD SLOT 3
OMNIPORT
OUTPUT
OUTPUT
INPUT
OUTPUT-1OMNIPORTOMNIPORTOMNIPORT OUTPUT-2OUTPUT-3
INPUT
OMNIPORT
FEED
LINK
12
INPUT
FEED
OFF
OFF
CARD SLOT 1CARD SLOT 2
OMNIPORT
OFF
OUTPUT OUTPUT
LINK
OFF
OUTPUT
INPUT
OUTPUT
INPUT
3
INPUT
CARD SLOT 3
OMNIPORT
OUTPUT
OUTPUT
INPUT
INPUT-1
INPUT
OMNIPORT
FEED
LINK
12
INPUT
FEED
OFF
OFF
CARD SLOT 1CARD SLOT 2
OMNIPORT
OFF
OUTPUT OUTPUT
LINK
OFF
OUTPUT
INPUT
OUTPUT
INPUT
3
INPUT
CARD SLOT 3
OMNIPORT
OUTPUT
OUTPUT
INPUT
INPUT-2
INPUT
OMNIPORT
FEED
LINK
12
INPUT
FEED
OFF
OFF
CARD SLOT 1CARD SLOT 2
OMNIPORT
OFF
OUTPUT OUTPUT
LINK
OFF
OUTPUT
INPUT
OUTPUT
INPUT
3
INPUT
CARD SLOT 3
OMNIPORT
OUTPUT
OUTPUT
INPUT
INPUT-3
SIGNAL FLOW
This ow chart shows the basic signal routing. The signal comes into the Cube via the rear
panel XLR female or ¼" TRS inputs. Once the signal goes into a module it is processed and
sent to the male XLR and parallel ¼" TRS output. From here the signal can be routed to the
next adjacent module via the FEED switch connection as described in the next section.
CARD SLOT I/O CONNECTIONS
Each of the Cube card slots is equipped with XLR and ¼" TRS inputs and outputs. The input
sensitivity will be dependant on the type of module being used. For instance if you are using
a microphone preamplier, the input will of course be suited for a low level microphone. If
you are using a dynamic processor like a limiter or an EQ, then the input will usually be set
to handle a professional +4dB balanced line-level signal.
INPUT
OMNIPORT
FEED
LINK
12
INPUT
FEED
OFF
OFF
CARD SLOT 1CARD SLOT 2
OMNIPORT
OFF
OUTPUT OUTPUT
LINK
OFF
OUTPUT
INPUT
OUTPUT
INPUT
3
INPUT
CARD SLOT 3
OMNIPORT
OUTPUT
OUTPUT
INPUT
Following 500 series convention, the XLR and TRS outputs usually produce a +4dB balanced
line level signal that is able to feed a professional recording system or line level mixing
console. Put simply, the input level is determined by the type of module being used while the
output level will typically be a balanced +4dB line level signal. If you use ¼" mono cables
you will unbalance the signal. This will reduce the level by about -6dB but everything will still
remain completely functional. Simply adjust the levels to compensate.
3
Bekijk gratis de handleiding van Radial Engineering Workhorse Cube, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Radial Engineering |
| Model | Workhorse Cube |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2522 MB |
