Radial Engineering Jensen Twin-Servo handleiding
Handleiding
Je bekijkt pagina 8 van 12
Radial Engineering Ltd.
Jensen Twin-Servo 500™ Module
True to the Music
®
5
There is a hidden ground lift switch (mini slider) that lets
you lift the ground on the front and rear XLR inputs. As the
Twin-Servo is equipped with an input transformer, you will
likely never need to lift the ground. This should be set in
the upward position. However, a unique situation could arise
where you may incur noise. To lift the ground, you have to
pull the module from your power rack and then move the
slider downwards towards the 15-pin card edge connector.
The ground lift switch does not affect the ¼” guitar input
portion of the Combo jack or the output side of the Twin-
Servo. Note that when the ground is lifted, the Twin-Servo
will no longer pass 48V phantom power to your microphone.
HI-Z Input and Omniport™
The Twin-Servo has two instrument input options. The
immediately obvious one is on the front panel - as part of the
Neutrik Combo connector. Note that this is a standard hi-Z
¼” instrument input and using a 1/4” TRS connector is not
recommended. The second is via the Omniport™ for those
that are equipped with a Radial 500 series power rack. Both
are connected in parallel but as soon as you engage the
front panel jack, it will automatically switch the rear panel
¼” input off.
Switch Located Here
WARNING NOTICE TO USER!
Although preventative safety measures have been designed into Radial 500 series
products we strictly advise against hot-swapping modules or plugging and
unplugging them when the Workhorse or other 500 series rack are powered on. Hot
swapping can cause connection sparks at the card-edge connector that could send
damaging transients to other equipment. This also greatly reduces the life span of the
contacts. Damage due to hot swapping is not covered under warranty. There are no
user serviceable parts inside.
+
INPUT
OMNIPORT
FEED
LINK
123456
OUTPUT
INPUT
78
SUMMING MIXER INPUTS 1 ~ 8
INPUT
FEED
LINK
INPUT
FEED
LINK
INPUT
FEED
LINK
INPUT
FEED
INPUT
FEED
INPUT
FEED
INPUT
OUTPUT
LEFT
WORKHORSE RACK & MIXER
RIGHT
LEFTRIGHT
EXPANSION
BUSS
GROUND
CHASSISCIRCUIT
DIRECT OUT 1 ~ 8INPUTS 1 ~ 8
OFF
OFF
CARD SLOT 1CARD SLOT 3CARD SLOT 5CARD SLOT 7 CARD SLOT 2CARD SLOT 4CARD SLOT 6CARD SLOT 8
OMNIPORTOMNIPORTOMNIPORTOMNIPORTOMNIPORTOMNIPORTOMNIPORT
Made in Canada
Radial Engineering Ltd.
1/4” TRS - TIP SEND / RING RETURN
INSERTINSERT
MAIN
OUT
MON
OUT
OFFOFF
OFF
OFFOFF
OFF
OFFOFF
OFF
OUTPUT OUTPUT OUTPUTOUTPUTOUTPUTOUTPUT OUTPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
PIN DIAGRAM - PANEL VIEW
1
-
+
G
-
+
G
2
3
-
+
G
-
+
G
4
5
-
G
6
7
8
13
IN
OUT
LEFT RIGHT
IN
OUT
SPLIT VOLTAGE POWER SUPPLY
+18VDC
COM
+48VDC
+18VDC
COM
POWER SUPPLY
ON
ON
MONO
2
3
41
LEVEL
CLIP
PAN
Made in Canada
LEVEL
ON
6
78
5
LEVEL
MAIN
MON
48V PHANTOM
+16V / -16V
LEVEL
CLIP
PAN
ON
LEVEL
CLIP
PAN
ON
LEVEL
CLIP
PAN
PANPANPANPAN
ON
LEVEL
CLIP
LEVEL
ON
LEVEL
CLIPON
LEVEL
CLIPON
LEVEL
CLIPON
REAR PANEL INPUT
(WORKHORSE)
Bekijk gratis de handleiding van Radial Engineering Jensen Twin-Servo, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Radial Engineering |
| Model | Jensen Twin-Servo |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2009 MB |
