Radial Engineering Jensen Twin-Servo handleiding
Handleiding
Je bekijkt pagina 6 van 12
Radial Engineering Ltd.
Jensen Twin-Servo 500™ Module
True to the Music
®
-12 -9
-3
-6
+6
+9
+12 +18
Made in Canada
OUTPUT LEVEL-VU
dB
+3
0
HPF
48V
PAD
180º
JENSEN TWIN
-
SERVO
12
I
I
I
I
I
I
I
I
I
I
I
28dB
35
42
48
56
60
22
15
9
6
OMNIPORT: INSTRUMENT INPUT
Radial
990
opamp
3
Radial ThumbSet™
knurled screws are
included for easy
installation.
+
INPUT
OMNIPORT
FEED
LINK
123456
OUTPUT
INPUT
78
SUMMING MIXER INPUTS 1 ~ 8
INPUT
FEED
LINK
INPUT
FEED
LINK
INPUT
FEED
LINK
INPUT
FEED
INPUT
FEED
INPUT
FEED
INPUT
OUTPUT
LEFT
WORKHORSE RACK & MIXER
RIGHT
LEFTRIGHT
EXPANSION
BUSS
GROUND
CHASSISCIRCUIT
DIRECT OUT 1 ~ 8INPUTS 1 ~ 8
OFF
OFF
CARD SLOT 1CARD SLOT 3CARD SLOT 5CARD SLOT 7 CARD SLOT 2CARD SLOT 4CARD SLOT 6CARD SLOT 8
OMNIPORTOMNIPORTOMNIPORTOMNIPORTOMNIPORTOMNIPORTOMNIPORT
Made in Canada
Radial Engineering Ltd.
1/4” TRS - TIP SEND / RING RETURN
INSERTINSERT
MAIN
OUT
MON
OUT
OFFOFF
OFF
OFFOFF
OFF
OFFOFF
OFF
OUTPUT OUTPUT OUTPUTOUTPUTOUTPUTOUTPUT OUTPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
PIN DIAGRAM - PANEL VIEW
1
-
+
G
-
+
G
2
3
-
+
G
-
+
G
4
5
-
G
6
7
8
13
IN
OUT
LEFT RIGHT
IN
OUT
SPLIT VOLTAGE POWER SUPPLY
+18VDC
COM
+48VDC
+18VDC
COM
POWER SUPPLY
ON
ON
MONO
2
3
41
LEVEL
CLIP
PAN
Made in Canada
LEVEL
ON
6
78
5
LEVEL
MAIN
MON
48V PHANTOM
+16V / -16V
LEVEL
CLIP
PAN
ON
LEVEL
CLIP
PAN
ON
LEVEL
CLIP
PAN
PANPANPANPAN
ON
LEVEL
CLIP
LEVEL
ON
LEVEL
CLIPON
LEVEL
CLIPON
LEVEL
CLIPON
Output
REAR PANEL
INPUT
(WORKHORSE)
mAkInG ConneCTIonS
Before making connections, ensure your audio
system is turned off and volume levels turned
down. Hot swapping or inserting the module into
a 500 series power rack when power is on is not
recommended as it can harm some equipment and
shorten the lifespan of the card edge connectors.
Gently slide the Twin-Servo module into place
ensuring you align the card edge with the 15-pin
receptacle. If you have a newer Radial Workhorse,
the nylon guides make this easy. The Twin-Servo
comes with a pair of handy ThumbSet™ thumb
screws. These should be hand-tightened to secure
the module in place before use.
Your power rack will likely be equipped with XLR inputs and outputs for each strip. Connect
your microphone to either the female XLR input on the rear panel or the handy front panel
Combo connector. These are wired in parallel and only one should be used at any one time.
Connect the output using the male XLR on the power rack to your recording system. Ensure
the volume levels on your recording system are turned off and set the volume control on the
Twin-Servo fully counter-clockwise to 7 o’clock. You are now ready to turn on your power rack
and recording system. Note that there is no power switch on the Twin-Servo. As soon as your
power rack is turned on, the Twin-Servo will spring to life.
If you are using a condenser microphone, activate the phantom power by depressing the
front panel 48V switch. All other switches should be in the out position. Slowly increase the
volume on your recording system and then turn up the volume on the Twin-Servo. It is always
best to test at low volumes as this will reduce the opportunity of damaging more sensitive
components such as tweeters should a connection be improperly seated. You should now
hear the audio and see activity on the 10 bar LED meter.
Bekijk gratis de handleiding van Radial Engineering Jensen Twin-Servo, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Radial Engineering |
| Model | Jensen Twin-Servo |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2009 MB |
