QSC Synapse D32o handleiding
Handleiding
Je bekijkt pagina 10 van 13
Attero Tech by QSC Synapse D32o
User Manual
Ó QSC, LLC 2020 614-00049
3 – Device Operation
Certain features of the D32o such as channel mutes, output
level, and front panel lockout are controlled using unIFY Control
Panel application. Details of those features are shown in the
help documentation for unIFY Control Panel.
Some features of the device are operated from the various
controls on the front panel such as the main display.
3.1 – Display View Operation
During power up the display will show the Attero Tech logo. Once
the device is running, the display will switch to showing a normal
view. If there are any problems, the display will indicate a POST
(Power-On Self-Test) error. If this happens contact Attero Tech
technical support.
Once up and running, the front panel can show various different
views and is used to control a number of D32o features. To save
power, the display will turn itself off after 30 seconds of inactivity.
To activate the display again, press either of the knobs to activate
their buttons or the monitor select button. The Display Timeout
timer can be adjusted in unIFY Control Panel.
*Note: Turning a knob will NOT turn the screen back on. It must
be a button push.
Navigating the views on the display is achieved using the “Menu
Nav” knob. Rotating this left or right will step through the various
views available. If the front panel lock has been activated by
unIFY, the panel lock icon will be shown in the upper right hand
corner of the display and while the “Menu Nav” knob can still be
used to rotate the different views no further action can be taken
on any view.
3.1.1 – Bank Metering Views
There are two views for bank metering. The main part of each
bank view shows meters for each analog output in that bank. This
view can be used to select the monitor output if the panel lock is
not active by pressing in the “Menu Nav” button. This activates a
cursor that can be scrolled used the knob to select one of the
visible channels. Once the desired channel is selected, press the
separate “Monitor Select” button and that channel will when be
routed to the headphone output.
3.1.2 – Channel Metering Views
Each individual output channel has its own view. The meter itself
is shown in the horizontally across the main part of the view from
left to right. The name of the current channels meter being shown
is displayed in the upper left hand corner. The name in
parenthesis that follows the name is the channel name that this
channels is identified by on the Dante™ network. This view can
also be used to select the monitor output if the front panel lock
is not active. To do so, with the desired channel on view, click the
“Monitor Select” button.
3.1.3 – Network Info View
The Network info view shows the IP addresses and link speed of
the D32o’s interfaces. In redundant mode, both a primary and a
secondary interface will be shown. The primary port speed will
always indicate the faster of the two possible primary links if they
are both used. The same is true the secondary port speed if both
secondary links are used.
In switched mode, only one interface with its IP address is shown
and the speed indicated will be the fastest speed of any of the
four possible links.
3.1.4 – Dante™ Info View
The Dante™ info view shows information about the Dante™ setup.
The device Dante™ name, its port mode and the devices clock
sync status are all shown. The Dante™ name is name the device
identifies itself as on the Dante™ network. The port state shows
if the device is in either redundant mode or switched mode. The
clock sync indicates whether the device is the “Master” clock for
the system or if it’s a “Slave” to another device. A state of “No
Sync” may indicate a possible problem with either the device or
the network.
Panel Lock
Headphone VolumeHeadpho ne Channel
Screen name
Channel Name (Dante Tx Name)
Headpho ne Channel
Headphone Volume
Bekijk gratis de handleiding van QSC Synapse D32o, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | QSC |
| Model | Synapse D32o |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3083 MB |
