Handleiding
Je bekijkt pagina 21 van 32
MODEL 1
Remove the 3 panels A as shown in Fig.4.
Pull handle B as shown in Fig.6.
MODEL 2
Open panel C as shown in Fig.5.
Pull handle B as shown in Fig.6.
If the appliance has a lid, remove it by removing the 4
screws B as shown in Fig.9A.
• WALL FIXING
Mark the position of the lower side of the hood on the wall
(Fig.2A). Maintain the minimum distance required from the
hob as shown in Fig.2B.
- Position the xing template on the wall, making sure
that the line coincides with the line previously made on
the wall.
- Mark the xing holes and cut them into the material
(Fig.3).
- Fix the 2 top screws K and screw anchors (Fig.3), without
tightening them completely.
- Place the appliance against the wall, align it in horizontal
position and tighten screws K (Fig.7).
- Once the adjustment has been completed, x the hood
using the 2 screws C (Fig.8).
- When carrying out the xing operations, use only screws
and screw anchors suited to the type of wall (e.g. reinforced
concrete, plasterboard etc.).
- If the screws and screw anchors are supplied with the
appliance, make sure that they are suited to the type of
wall to which the hood must be xed.
• INSTALLATION OF MODELS WITHOuT DECORATIVE
DuCTS
EXTRACTOR HOOD
- Remove the 4 screws B as shown in (Fig.9A).
- Remove both grid E on the air outlet hole and lid M as
shown in (Fig.9B).
- Connect the hood to the exible hose (not supplied)
and the hose to the air exhaust hole previously prepared
(Fig.9C).
- Fix the lid once again by using the 4 screws previously
removed in (Fig.9A).
• OPTIONAL ACCESSORIES
This model may have decorative ducts as optional
accessories - ask your retailer for information.
Before xing the decorative ducts, remove both the 4
screws B and lid M, as shown in (Fig.10A-B).
A sound-absorbing kit is also available (to be ordered as an
OPTIONAL accessory) in order to increase the quietness
level of the hood. The sound-absorbing layer must be
applied to the back of the decorative panel. For xing
operations, refer to the instructions supplied with the kit.
• INSTALLATION OF MODELS WITH DECORATIVE
DuCTS
Make sure the electrical power supply is within the
measurements of the decorative connector.
Adjust the width of the support bracket of the top connector
(Fig.11C). Then x it to the ceiling so that it is on the same
axis as the hood using screws A (Fig.11C) adhering to
the distance from the ceiling shown in (Fig.11B). Connect
ange C to the air exhaust hole using exible hose L
(Fig.11D).
Slide the top duct into the bottom duct. Fix the bottom duct
to the hood using screws B (supplied) (Fig.11E).
Pull out the top duct as far as the bracket and x it using
screws F (Fig.11C).
• FILTER HOOD
Please note:
The lters should be ordered as accessories from your
retailer.
We offer 2 different types of kit which can be used to
transform the EXTRACTOR hood into a FILTER hood, in
accordance with the type of appliance model purchased.
One kit contains extractable lters (g. 10) and the other
contains circular lters (g. 15).
1- If you nd a bracket (such as the one indicated in g.
14) included in the product packaging, this should be xed
to the hood using the 6 screws supplied.
To replace the active carbon lters pull lever B outwards
as shown in (Fig.10).
2- If your product is not supplied with a bracket, this means
that the active carbon lter is a circular version (g. 15).
The lters should be tted to the extraction assembly inside
the hood, by centring them and rotating them 90 degrees,
until they click into place (Fig. 15).
USE AND MAINTENANCE
• It is recommended to operate the appliance prior to
cooking.
It is recommended to leave the appliance in operation
for 15 minutes after cooking is terminated in order to
completely eliminate cooking vapours and odours.
The proper function of the cooker hood is conditioned by
the regularity of the maintenance operations, in particular,
the active carbon lter.
• The anti-grease lters capture the grease particles
suspended in the air, and are therefore subject to clogging
according to the frequency of the use of the appliance.
In order to prevent re hazard, it is recommendable to
clean the lter at a maximum of 2 months by carrying out
the following instructions:
- Remove the lters from the cooker hood and wash
them in a solution of water and neutral liquid detergent,
leaving to soak.
- Rinse thoroughly with warm water and leave to dry.
- The lters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several
washes. This is not cause for customer complaint nor
replacement of panels.
• The active carbon lters purify the air that is replaced
in the environment. The lters are not washable nor
re-useable and must be replaced at maximum every
four months. The saturation of the active carbon lter
depends on the frequency of use of the appliance, by
the type of cooking and the regularity of cleaning the
anti-grease lters.
• Clean the fan and other surfaces of the cooker hood
regularly using a cloth moistened with denatured alcohol
or non abrasive liquid detergent.
- 21 -
Bekijk gratis de handleiding van Prima LIA730, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Prima |
| Model | LIA730 |
| Categorie | Afzuigkap |
| Taal | Nederlands |
| Grootte | 4234 MB |
