Premium Levella PM70710 handleiding
Handleiding
Je bekijkt pagina 15 van 23
14
front door plate
latch switch holder
screw
Fig.4-21
Fig.4-22
light tough switch
PC board
control panel
Fig.4-23
control panel
light tough switch
(2) Assemble the interlock switch and pilot switch to the switch holder, make sure they are assembled correctly.
(3) Tightly fix the holder with two screws.
(4) Check the position of the hook and the switch holder.
Close the door, push and pull the low and up part of the door
to check whether the door is flexible. If it does, back and
front position of the holder should be adjusted. Provided the
up hook is loose, the door should be pushed more closely to
the oven, and pull the holder inside closely after loosen the
screw which fix the holder, then, tighten the screw and check
whether it is still loose. If it is not or the loose is minor, it
would be OK. Open the door, then close it lightly, check
whether the hook is in position, if not, readjustment is
needed. If the loose is at lower part of the door, the adjust
methods is the same with the above said steps but the
screw is the one below (FIG.4 - 21).
4
4
.
.
1
1
1
1
T
T
H
H
E
E
C
C
O
O
N
N
T
T
R
R
O
O
L
L
P
P
A
A
N
N
E
E
L
L
O
O
F
F
A
A
T
T
Y
Y
P
P
I
I
C
C
A
A
L
L
M
M
I
I
C
C
R
R
O
O
W
W
A
A
V
V
E
E
O
O
V
V
E
E
N
N
Pull out the power plug.
Take off the cabinet.
Discharge between one end of the capacitor and the
baseboard with a screwdriver.
Means of dismantling the PC board and door release
mechanism:
(1) Pull out all the terminal plug of the PC board.
(2) Loosen out the two screws which fix the control panel
with a “+”- screwdriver (FIG.4 -6).
(3) Take off the control panel.
(4) Take off the three “+”- screws which fix the PC board
as the FIG.4 – 22.
(5) Take off the range terminal plugs as FIG.4 – 24 shown,
that is press the two places according to the arrow
direction at the figure, while pull it up about 2mm, then off
the row plastic board.
(6) Take off the PC frame.
(7) Tear off the undried glue of the light touch switch (FIG.4
- 23).
to assemble the PC board and door release mechanism,
(1) Tear off the undried glue patch of the light tough switch
(1) and (2) as the Fig.shown, and place them into the
rectangle hole of the surface of the plastic board.
(2) After uprighted the light tough switch, tear off the
protective paper on the back, and stick it on the plastic
board smoothly.
(3) Tear off the protective paper of the light touch switch (2), and stick the switch on the back of the plastic board
smoothly.
(4) Assemble in the PC frame and PC board as FIG .4 –22,
and fix them with three “+”- screwes.
(5) Fix the range wires as FIG.4-24, the means are: Insert
the range wires first, make sure that its notch is tallied with
the flange of the row seat, then, press it down to its normal
position.
8
9
Bekijk gratis de handleiding van Premium Levella PM70710, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Premium Levella |
| Model | PM70710 |
| Categorie | Magnetron |
| Taal | Nederlands |
| Grootte | 4399 MB |
