Practixx PX-BTS-450 handleiding
Handleiding
Je bekijkt pagina 21 van 44
w ww.practixx.com
GB
|
21
• If the machine tends to tilt or walk (especially when
sanding long and heavy panels), it must be fas-
tened to a solid surface of sucient carrying force.
• Make sure the sanding belt runs in the correct di-
rection. See arrows at the back of the belt.
• Make sure the sanding belt is running correctly so
that it cannot come o the drive pulleys.
• Make sure the sanding belt is not twisted or loose.
• Firmly hold the workpiece when sanding.
• Always use the end stop when using the belt sand-
er in a horizontal position.
• Always hold the workpiece rmly against the table
when using the disc sander.
• Always hold the workpiece to the side of the sand-
ing disc running downwards, in order to maintain
the workpiece pressed to the table. By using the
upward-running side of the sanding disc, the work-
piece could be ejected and cause injury to per-
sons.
• Always keep a minimum distance of about 1.6 mm
or less between the table or stop and the sanding
belt or disc.
• Do not wear gloves. Do not hold the workpiece
with a cloth during sanding.
• Use sanding belt or disc of the correct grit corre-
sponding with the wood.
• Never sand workpieces too small to be held safely.
• Avoid awkward hand positions where a sudden slip
could cause your hand to touch the sanding belt
or disc.
• When sanding a large piece of material, provide
an additional support at table height.
• Never sand an unsupported workpiece. Secure the
workpiece with the table or the stop. Exceptions
are the sanding of curved workpieces on the out-
side of the sanding disc.
• Always clear the table, fence or sanding belt of
scraps or other objects, before turning the ma-
chine on.
• Do not perform any layout assembly or set-up work
on the table while the sander is in operation.
• Switch the machine o and pull the power plug
from the socket when tting or removing acces-
sories.
• Never leave the working area of the sander while
the tool is running, or as long as it has not come
to an absolute standstill.
• Always place the workpiece on the sanding table
or position it rmly against the sanding stop. Place
curved tools securely on the table when sanding
on the sanding disc.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may aect the power tool’s operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the pow-
er tool for operations dierent from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a qualied
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Warning! This power tool generates an electromag-
netic eld during operation. This eld can impair
active or passive medical implants under certain cir-
cumstances. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the power tool.
Additional safety rules for the belt and disc
sander
Warning: Do not use your machine until it is com-
pletely assembled and installed according to the in-
structions.
• If you are not familiar with the operation of the
sander, ask the head of the department, your
teacher, or any other qualied person.
• Attention: This machine is designed for grinding wood
or wood-like material only. The sanding of other mate-
rials can cause re, injuries, or damage the product.
• Always wear safety goggles.
• This machine may only be operated indoors.
• Important: Mount and use the machine on a hori-
zontal surface. A non-horizontal surface can dam-
age the motor.
Bekijk gratis de handleiding van Practixx PX-BTS-450, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Practixx |
| Model | PX-BTS-450 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8286 MB |
