Power Soak SS-S handleiding
Handleiding
Je bekijkt pagina 4 van 5
4 OM-SILVER SOAK PRE-WASHING SYSTEM
TROUBLESHOOTING
DANGER: ONLY A LIMITED NUMBER OF TROUBLESHOOTING AND REPAIR
PROCEDURES MAY BE PERFORMED BY THE FACILITY OWNER OR
MANAGER. ANY TROUBLESHOOTING OR REPAIR THAT REQUIRES THE
REMOVAL OF FASTENERS OR THAT ENTAILS ELECTRICAL SERVICE MUST
NOT BE ATTEMPTED BY ANYONE OTHER THAN AN AUTHORIZED SERVICE
AGENCY. TO OBTAIN THE NAME OF A RECOMMENDED SERVICE AGENT IN
YOUR AREA, PLEASE CALL POWER SOAK AT 888-994-7636.
If the above trouble shooting procedures do not correct the problem, you may
contact Power Soak at 888-994-7636 or an authorized service agency.
SYMPTOM POSSIBLE CAUSE PROCEDURE
Pump motor
will not run
Circuit breaker
accidentally turned off
Turn breaker on
Circuit breaker tripped
Investigate reason for tripping, e.g.
damaged wiring, undersized breaker.
CONTACT POWER SOAK SERVICE OR AN
AUTHORIZED SERVICE AGENCY.
Power cord
unplugged (mobile
models so equipped)
Reconnect plug
Motor thermal
overload tripped
Investigate reason for overload tripping,
e.g. debris stuck in pump impeller. If debris
removal requires that you remove any
fasteners, YOU MUST CONTACT POWER
SOAK SERVICE OR AN AUTHORIZED
SERVICE AGENCY. Once rectied, reset
thermal overload by pressing button on
bottom of motor junction box.
Start capacitor
defective (single
phase motors)
Replace capacitor. To do this, YOU MUST
CONTACT POWER SOAK SERVICE OR AN
AUTHORIZED SERVICE AGENCY.
Pump motor
runs, but
water ow is
inadequate
Motor is running on
the wrong voltage
Conrm that the house wiring supply is
appropriate for the motor nameplate data.
Reconnect motor internal leads according
to the motor nameplate instructions. YOU
MUST CONTACT POWER SOAK SERVICE
OR AN AUTHORIZED SERVICE AGENCY to
make these changes.
Motor is running the
wrong direction
For three phase motors, reverse any two
motor leads. For single phase motors,
reconnect motor internal leads according
to the motor nameplate instructions. YOU
MUST CONTACT POWER SOAK SERVICE
OR AN AUTHORIZED SERVICE AGENCY to
safely change the rotation.
Unit makes a
loud, steady
noise when
running
Debris caught in the
motor’s cooling fan
Lock and tag out the electrical power from
the unit, remove the motor fan cover, and
remove the debris. Replace the fan cover
and restore the power. For this task, YOU
MUST CONTACT POWER SOAK SERVICE OR
AN AUTHORIZED SERVICE AGENCY.
Motor seal running
dry
Lock and tag out the electrical power
from the unit, remove the motor fan cover,
and squirt some low viscosity oil such as
WD40 between the fan and the motor end
bell. Replace the fan cover and restore the
power. YOU MUST CONTACT POWER SOAK
SERVICE OR AN AUTHORIZED SERVICE
AGENCY for service of this nature.
Debris caught in the
pump impeller
Lock and tag out the electrical power from
the unit. Remove the four 1/4-20 x 1-1/4
impeller shroud retaining screws adjacent
to the motor. Remove the basket and lift
the impeller shroud out. Remove debris
from the impeller and reassemble. YOU
MUST CONTACT POWER SOAK SERVICE
OR AN AUTHORIZED SERVICE AGENCY for
this service.
Silverware
is not
getting clean
Unit is being lled with
cold water
Drain and rell with 115°F water.
Pieces are nesting
Avoid sorting the pieces by type, e.g. all
spoons being washed, followed by all forks
being washed, etc.
Too much food soil is
being left on the
silverware when the
basket is loaded
Rinse off heavy accumulations of food
soils before the pieces are loaded into
the basket. This will avoid weakening the
detergent.
Food soils are dried
onto the silverware
before being loaded
into the basket
Allow the silverware to pre-wash for a
longer period of time.
Basket is being
overloaded
Remove silverware until the level is at or
below the ll line inside the basket. Spread
the silverware out into a uniformly thin
layer on the basket bottom. Do not allow
the silverware to remain in a thick pile.
Ineffective detergent
is being used
Consult with your chemical supplier to
determine the best chemical for your
application.
Low water level
Water level should be even with the ll line
inside the basket when the unit is off.
Exhausted detergent
Drain the unit and rell it with fresh
detergent and 115°F water. Experiment
with refreshing the water and detergent
more often.
Insufcient detergent
Follow the chemical supplier’s instructions
exactly for best results.
Insufcient wash time
Highly intricate silverware and stubborn
soils will require extra wash time.
Bekijk gratis de handleiding van Power Soak SS-S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Power Soak |
| Model | SS-S |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2070 MB |
