Power Soak Power Prep PPA4B-84 handleiding

Niet gecategoriseerd

Power Soak

12 pagina's

PDF beschikbaar

Handleiding

6 OM-POWER PREP ADVANCED

IMPORTANT

: THE MOTOR MUST ROTATE IN THE CORRECT DIRECTION FOR THE MACHINE

TO OPERATE PROPERLY.

Shelving

Reinstall any shelving that was removed for convenience of installation. If the shelving

is damaged or corroded, it is recommended that the shelving be replaced. Remember

that whatever equipment or supplies are located above the sink might accidentally fall

into the food being processed by the Power Prep Advanced.

VALIDATING THE INSTALLATION

IMPORTANT

: MOTOR ROTATION MUST BE CORRECT FOR THE MACHINE TO OPERATE

CORRECTLY.

TESTING THE COMPONENTS

Check for Leaks

• Turn on the water supply and inspect all joints for leaks.

• Close the drain valve(s), ll the sink(s) with water, and inspect the drain ttings for

leaks.

• Open the drain valve(s) and inspect the drain joins for leaks as the water is

draining from the sink.

Check the Electrical Installation

• Verify that there are no loose wires or open holes in the electrical enclosure.

• Fill the wash sink with water and turn the control handle to ON. Have a qualied

electrician verify that the amp draw on the electrical supply is within the

specications on the identication tag.

• Check motor rotation for the correct direction as indicated by the arrow on the

pump housing.

Check the Faucet Operation

• Open each faucet knob and verify that water ows from each hand control. Verify

that hot and cold water are running from the correct hand control.

• With the water valves open, turn the center knob to see that it will shut off ow to

the faucet and that the hand sprayer is still functional.

• Purge the water lines according to local code requirements.

IMPORTANT

: INSTALLER IS RESPONSIBLE FOR ALL PLUMBING TO CONFORM TO LOCAL

BUILDING CODES WHICH MAY BE DIFFERENT FROM ILLUSTRATIONS

SHOWN IN THIS MANUAL.

Plumbing Connections

Connect the water supply lines to the faucets. Connect all the drains to the waste

drain connection.

DO NOT USE HOSES to make the pressure connections to the faucets. Maximum

water inlet pressure is not to exceed 125 psi (8.6 Bar), minimum water pressure to be

not less than 50 psi (1.2 Bar).

Electrical Connections

An equipotential bonding terminal is provided on the side

of the wash sink near the serial tag and identied with

the symbol shown at right. This terminal is used to make

a connection for properly grounding the machine. This

connection must be completed by a qualied electrical

technician.

The nal electrical connections between the Power Prep

Advanced and the electrical supply must be made by a

licensed electrician. The Power Prep Advanced has several

options for motors. Review the information tag on the side

of the wash tank or the pump motor for determining the specic requirements of

the electrical system (See Verify the Electric Requirements section of this instruction

booklet).

CAUTION

: DO NOT RUN THE POWER PREP ADVANCED EMPTY FOR MORE THAN A

FEW SECONDS. DRY OPERATION OF THE PUMP WILL OVERHEAT THE PUMP

SEAL.

Checking the Motor Rotation

The motor must rotate in the correct direction in order for the Power Prep Advanced

to function properly. An arrow indicating the direction of rotation is located on the

pump housing. Running the motor in the wrong direction does not damage the motor

or pump, but the pump will not circulate water in the wash sink correctly. After the

connection to the electrical supply is properly made, turn the motor on momentarily

and watch the cooling fan blades on the end of the motor to see that the motor is

turning in the correct direction. The fan blades can be seen through the vent holes

on the end of the motor. It is usually necessary to watch the fan as the motor coasts

to a stop, because the fan is difcult to see when the motor is running at full speed.

Bekijk gratis de handleiding van Power Soak Power Prep PPA4B-84, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.