Phonic DMP808 handleiding
Handleiding
Je bekijkt pagina 25 van 56
23
English
DMP808 / DMP808D
Parametric Equalizers
EQ On/O Button: This button can turn the Equalizer
for the currently selected channel on and o.
Reset: Push the reset button to restore all parameters
back to default.
EQ Band On/O: Use these buttons to turn the
corresponding EQ bands on and o. While not named
specically, these bands can be thought of as the low,
low-mid, high-mid and high frequency bands on your
average 4-band EQ.
EQ Type: For the rst and fourth bands on the EQ, users
can select the type of curve used for the EQ. Band 1
can be swapped between a normal EQ band (PEAK),
low shelf lter (SHELF), and high pass lter (CUT). Band
4 can be selected between an EQ band (PEAK), high
shelf lter (SHELF), and low pass lter (CUT). The Low/
High Pass Filters will cut frequencies above and below
the selected frequencies at 18 dB per octave. High and
Low Shelf lters act similarly, but cut frequencies below
the selected frequency by the preset level determined
by the user.
EQ Parameters: The EQ oers users the ability to view
or edit various parameters/properties of their EQ bands,
including the Gain (dB), the frequency (Hz/kHz) and the
‘Q’ of the EQ band.
Meters: Both input and output meters are available for
this process, essentially showing the dierence in the
overall signal level after equalization.
Feedback Silencer
Feedback occurs when the sound from your speakers
makes its way back into the mixer through microphones.
The audio look causes a high pitch squeal or screech
that can easily ruin your performance. Feedback can be
removed, however, by reducing or removing the problem
I don’t have any output
Have you activated the output channels? Do you see a
signal in the output meters? Have you correctly routed
your inputs to channels, turned levels up, and unmuted
mixes? Have you applied an excessive compressor-
limiter to any input or output signals?
I have a signal, but it’s really distorted!
Are any of the Clip LEDs lighting up for input or output
mixes? Do any of the signals on your entire audio chain
seem excessive? This could include input connectors,
channel inputs, matrix outputs.
My devices are not communicating via Ethernet
Are the red and green LEDs on the Ethernet connectors
lighting up? Are you using a decent quality Ethernet
cable?
My DMP808 won’t communicate with my computer
Are you using a decent quality Ethernet cable? Are your
computer and DMP808 both connected to the same
network? Do you have a rewall turned on?
frequencies. With a razor-thin lter, feedback can be
completely removed without aecting your audio what-
so-ever.
The DMP808 features a 12 lter feedback silencer.
This can operate in 2 dierent modes: Automatic and
Manual. When set to automatic, the activated lters will
automatically search for and remove feedback. When
set to manual, the user is able to adjust the frequency,
gain and Q of the individual lters.
Parameters: When the Feedback Silencer is set to
“Manual” it oers users the ability to view or edit various
parameters/properties of their EQ bands, including the
Gain (dB), the frequency (Hz/kHz) and the ‘Q’ of the 12
lters.
Threshold: Adjusting the threshold will determine
the level of signal required for the automatic feedback
silencer to kick in.
31-band GEQ
Graphic equalizers are fantastic in live setups where you
may need to compensate for room acoustics or other
factors. Include a 31-band graphic equalizer on your
speaker output signals to better rene your live audio.
Frequency bands: The GEQ’s frequency bands can be
boost or cut by the user. Frequencies are set at xed
frequencies between 20Hz and 20kHz.
TROUBLESHOOTING
How can I use the RS-232 port?
An RS-232 connection is available on the DMP808 to
allow control information to be sent to the unit without the
need of Ethernet connection. Asystems has provided an
implementation reference on the website.
Initializing the DMP808
The DMP808 can be initialized using the DIP switch on
the rear of the device. The left-most pin will allow users
to begin initializing the unit. It can be returned to the
RESUME position to continue operation.
Why are the front panel VRs not working?
The rear panel has a DIP switch that controls these VRs.
If set to the lower position these will be locked and you
will be unable to use them.
Bekijk gratis de handleiding van Phonic DMP808, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Phonic |
| Model | DMP808 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11121 MB |
