Philips BT7665 handleiding

Scheerapparat

Philips

2 pagina's

PDF beschikbaar

Handleiding

3000.135.0846.1 (24/02/2025)

supervision or instruction concerning use of the

product by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the product.

- Use this product only for its intended household

use as described in this manual. Misuse can lead to

hazards or serious injuries. Do not use attachments

not recommended by Philips Electronics Ltd

(Canada).

- Never operate this product if it has a damaged

USB power source, if it is not working properly,

after it has been dropped or damaged, or after

the product or the USB power source has been

dropped into water. For assistance call 1-866-800-

9311.

- Keep the USB cable and the USB power source

away from heated surfaces.

- Never drop or insert any object into any opening.

- Do not use the USB power source in or near a

power outlet that contains an electric air freshener

to prevent damage to the USB power source.

- Do not use product outdoors or operate where

aerosol (spray) products are being used or where

oxygen is being administered.

- Always check cutting units and other attachments

and accessories before you use the product. Never

use the product with a damaged cutting unit,

attachment or accessory, as injury may occur.

- Always attach the USB cable to the USB power

source and the product rst, then attach the USB

power source to the power outlet. To disconnect,

set all controls to 'o' position. Then remove the

USB power source from the power outlet.

- Plug USB power source directly into power outlet.

Do not use an extension cord.

- Unplug USB power source before plugging in or

unplugging the product.

- The batteries used in this product may present

a re or chemical burn hazard if mistreated. Do

not disassemble, heat above 100°C (212°F) or

incinerate.

- Only use original Philips accessories or

consumables.

- Charge, use and store the product at a

temperature between 10°C and 35°C.

- Keep product and batteries away from re and

do not expose them to direct sunlight or high

temperatures.

- If the product becomes abnormally hot or smelly,

changes color or if charging takes longer than

usual, stop using and charging the product and

contact Philips.

- Do not place products and their batteries in

microwave ovens or on induction cookers.

- Do not open, modify, pierce, damage or dismantle

the product or battery to prevent batteries

from heating up or releasing toxic or hazardous

substances. Do not short-circuit, overcharge or

reverse charge batteries.

- If batteries are damaged or leaking, avoid contact

with the skin or eyes. If this occurs, immediately

rinse well with water and seek medical care.

- When you handle batteries, make sure that your

hands, the product and the batteries are dry.

- To avoid accidental short-circuiting of batteries

after removal, do not let battery terminals come

into contact with metal objects (e.g. coins,

hairpins, rings). Do not wrap batteries in aluminum

foil. Tape battery terminals or put batteries in a

plastic bag before you discard them.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic elds.

SAVE THESE INSTRUCTIONS

Introduction

Congratulations on your purchase and welcome to

Philips.

To fully benet from the support that Philips oers,

You can nd the model number on the back of your

product.

The full model number (e.g. BT1234/56) is located on

the bottom of the packaging, your receipt or order

conrmation.

IMPORTANT TO KNOW

- Charge the appliance fully before you use it for the

rst time.

- This appliance is waterproof. It is suitable for use in

the bath or shower and for cleaning under the tap.

- For safety reasons, the appliance can only be used

without cord.

- This appliance is intended for trimming facial hair

to the desired length. Do not use the appliance to

trim body or scalp hair.

- You can use the hair collector to catch hair while

trimming. Use the hair collector with the cutting

element alone or with an adjustable comb

attached (Fig. 2).

- Switch o the appliance before removing or

attaching attachments and before cleaning.

- Clean the appliance after each use (see 'Cleaning').

General description (Fig. 1)

1 Precision trimmer

2 Cutting element

3 Hair collector

4 Hair length setting wheel

5 On/o button

6 Battery status indicator

7 Socket for small plug

8 Small plug

9 USB cable

Note: The power source is not included. A suitable

power source (e.g. Philips HQ87) is available via

www.philips.com/support.

10 Adjustable trimming comb 0.4 mm – 10 mm

11 Adjustable trimming comb 10.4 mm – 20 mm

12 Fading comb 1 mm – 5 mm (only with models

BT5785, BT7665)

13 Fading comb 5 mm – 1 mm (only with models

BT5785, BT7665)

14 Charging stand (only with models BT5785,

BT7665)

Not shown: storage pouch, brush

Charging

- Charging or using the appliance at temperatures

below 10 °C or higher than 35 °C adversely aects

the lifespan of the battery.

- If the appliance is subjected to a major change

in temperature, pressure or humidity, let the

appliance acclimatize for 30 minutes before use.

- The USB power source is not included. To safely

charge your product, only use a certied IPX4

power source with output rating 5 V, ≥ 1.

Battery status indicator

Battery status Indicator mode

Almost empty Flashing orange light

Charging Flashing white light

Fully charged Solid white light

Note: Approx. 60 seconds after the battery is fully

charged, the battery status indicator switches o

automatically.

Charge the appliance before rst use and when the

battery status indicator shows that the battery is

almost empty. When the appliance has charged for

60 minutes, it has a cordless operating time of up to

100 minutes (models BT5775, BT5785) or 120 minutes

(model BT7665).

Warning: Keep the USB cable and the USB

power source dry.

Charging with an USB power source

1 Make sure the appliance is switched o.

2 Insert the small plug of the USB cable into the

socket in the bottom of the appliance (Fig. 3).

3 Insert the USB plug into the USB power source (not

included) (Fig. 5).

4 Insert the USB power source into the power outlet

(Fig. 6).

5 After charging, remove the USB power source

from the power outlet and pull the small plug out

of the appliance.

Charging with the charging stand (BT5785,

BT7665)

1 Make sure the appliance is switched o.

2 Insert the small plug into the charging stand

(Fig. 4).

3 Insert the USB plug into the USB power source (not

included) (Fig. 5).

4 Insert the USB power source into the power outlet

(Fig. 6).

5 Put the appliance in the charging stand (Fig. 7).

6 After charging, take the appliance out from the

charging stand, remove the power source from the

power outlet, pull the USB plug out of the power

source and then pull the small plug out of the

charging stand.

Quick charge

After approx. 5 minutes of charging, the appliance

contains enough power for one trimming session.

Using the appliance

Always check the appliance and all accessories

before use. Do not use the appliance or any

accessory if it is damaged, as this may cause injury.

Always replace a damaged part with one of the

original type.

Because of hygiene, only one person should use

the appliance.

Changing attachments

Attaching and detaching the hair collector

If you use the hair collector together with an

adjustable trimming comb, rst attach the hair

collector and then the trimming comb. To detach,

rst remove the trimming comb and then the hair

collector.

1 To attach the hair collector, align the top wings of

the hair collector with the top of the handle and

press the hair collector down until both sides click

into place (Fig. 8).

2 To detach the hair collector, place your hand

around the hair collector to prevent it from falling.

Then use your thumb to unhook one of the wings

of the hair collector and remove the hair collector

from the handle (Fig. 9).

Hold the appliance over a bin when detaching the

hair collector to avoid spilling the hairs.

Attaching and detaching the adjustable

trimming combs

1 To attach an adjustable trimming comb onto the

appliance, slide the comb legs straight into the

guiding grooves of the appliance until the comb

clicks into place (Fig. 10).

2 To detach an adjustable trimming comb from the

appliance, hold the comb on both sides and gently

pull it upwards o the appliance (Fig. 11).

Attaching and detaching the fading combs

1 To attach a fading comb onto the cutting

element,slide the front part of the comb onto the

teeth and press the plastic notch at the back of the

comb downwards until it clicks into place (Fig. 12).

2 To detach a fading comb from the cutting

element, carefully push the back part of the comb

o the appliance and then slide it o the cutting

element (Fig. 13).

Detaching and attaching cutting elements

1 To detach a cutting element, place your thumb

below the teeth of the cutting element and gently

push upwards until the cutting element comes o

the handle (Fig. 14).

2 To attach a cutting element, insert the plastic

notch at the back of the cutting element into the

guiding slot in the handle. Then gently press the

teeth of the cutting element downwards until the

cutting element clicks into place (Fig. 15).

Switching the appliance on and o

To switch the appliance on or o, press the on/o

button once (Fig. 16).

Trimming tips

- When trimming for the rst time, start by using the

comb with the maximum trimming length setting

to familiarize yourself with the appliance.

- Since hairs do not all grow in the same direction,

you may want to try dierent trimming positions

(i.e. upwards, downwards, or across). Practice is

best for optimum results.

When using the hair collector, hold the appliance

upwards to prevent caught hair from spilling.

- Always make smooth and gentle movements and

make sure that the surface of the comb always

stays in contact with your skin.

- When too many hairs have accumulated on the

appliance, remove the hairs before and/or during

use, for best trimming results (see 'Cleaning').

Using the hair collector

Using the hair collector is optional. Use the hair

collector to catch hair during trimming for easier

cleaning afterwards.

The hair collector is designed to catch some, but not

all the cut hairs. It is normal for some hairs to fall

down during trimming.

You can use the hair collector with the following

attachments:

Attachment Used with hair

collector

Cutting element yes

Adjustable trimming

combs

yes

Fading combs no

Precision trimmer no

Trimming without comb

Use the appliance without any comb and with or

without the hair collector to trim your beard close to

the skin, to a length of approx. 0.4mm.

1 Attach the hair collector to the appliance

(optional).

2 Switch on the appliance.

3 Place the at side of the cutting element against

your skin and make strokes against the direction of

hair growth (Fig. 17).

4 Switch o and clean the appliance after each use

(see 'Cleaning').

Trimming with adjustable trimming combs

Use the adjustable trimming comb attached to the

cutting element and with or without the hair collector

to trim your beard and mustache in your preferred

style.

Your appliance comes with two adjustable trimming

combs. You can choose from settings ranging from

0.4 mm to 10 mm and from 10.4 mm to 20 mm.

1 Attach the hair collector to the appliance

(optional).

2 Attach the adjustable trimming comb to the

appliance (see 'Changing attachments').

3 Turn the hair length setting wheel to select the

desired hair length setting (Fig. 18). The settings

on the wheel correspond to the remaining hair

length after trimming. The selected hair length

setting is shown in the center of the wheel.

4 Switch on the appliance.

5 To trim most eectively, move the appliance

against the hair growth direction. Make sure that

the surface of the comb always stays in contact

with the skin.

6 Switch o and clean the appliance after each use

(see 'Cleaning').

Edging without the hair collector

Use the appliance without any comb and without the

hair collector to trim edges and single hairs.

1 Detach any comb from the product (see 'Changing

attachments').

2 Detach the hair collector from the appliance (see

'Changing attachments').

3 Switch on the appliance.

4 Hold the cutting element perpendicular to the

skin. Make well-controlled movements to remove

unwanted hairs. Touch the hair lightly with the

trimmer (Fig. 19).

5 Switch o and clean the appliance after each use

(see 'Cleaning').

Fading hair combs (only BT5785, BT7665)

Use the cutting element with a fading comb but

without the hair collector to create a faded beard line.

The product comes with 2 fading combs. Each comb

can be used to trim one side of your face.

6 Attach one of the fading combs to the appliance.

1 Place the trimmer on your face close to the ear so

that the short teeth of the comb are higher and

the long teeth are lower (Fig. 20).

2 Switch the appliance on.

3 Move the trimmer once in a straight line from the

ear to the corner of your mouth to achieve a faded

beard style (Fig. 21).

4 Attach the other fading comb to trim the other

side of your face into a faded beard style.

5 Gently shake the hairs o the appliance in

between strokes to prevent hairs from collecting

between the cutting element and the comb.

6 Switch o and clean the appliance after each use.

Precision trimmer (only BT7665)

Use the precision trimmer without the hair collector to

create ne lines and contours around your facial style

close to the skin, to a length of 0.5mm.

1 Detach the cutting element from the appliance.

2 Attach the precision trimmer to the appliance.

3 Switch on the appliance.

4 Hold the precision trimmer perpendicular to

the skin and move the trimmer upwards or

downwards with gentle pressure (Fig. 22).

5 Switch o and clean the appliance after each use

(see 'Cleaning').

Cleaning

Switch o the appliance before removing or

attaching attachments.

Only use cold or lukewarm water to clean the

appliance.

Never use scouring pads, abrasive cleaning agents

or aggressive liquids such as petrol or acetone to

clean the appliance.

Never dry the cutting element with a towel or

tissue, as they may get caught in the teeth and

cause damage.

1 Make sure that the appliance is switched o and

removed from the charging stand or power outlet.

2 First detach any comb and then remove the

hair collector, if attached to the appliance (see

'Changing attachments'). Make sure you hold the

appliance over a bin or sink for easier clean-up.

3 Empty the hair collector into a bin (Fig. 23). Use

the cleaning brush to remove all the hairs from the

hair collector and from the comb.

4 Clean the whole handle under the tap or wipe it

clean with a dry or moist cloth.

5 Detach the cutting element from the appliance

and clean it with a brush.

6 Rinse all the attachments under the tap (Fig. 24).

7 Carefully shake o excess water and let all parts

air-dry completely.

Storage

Note: Do not place or store the appliance where it

can fall or be pulled into a tub or sink, water or other

liquid while plugged in.

- Make sure that the appliance is switched o and

that the USB power source has been removed

from the power outlet and from the appliance.

- Do not wrap the USB cable around the appliance

when storing.

- Store the appliance, the USB power source and

all the accessories in the pouch supplied. Attach a

comb to the cutting element to protect the teeth

during storage.

- Place the pouch in a safe, dry location, where it will

not be crushed, banged, or subject to damage.

- Make sure that the appliance and the accessories

are dry before you place them in the pouch.

Assistance

For all product support, please visit

www.philips.com/support.

Ordering accessories

To buy accessories or spare parts, visit

www.philips.com/parts-and-accessories or go to

your Philips dealer. You can also contact the Philips

Consumer Care Center in your country (see the

international warranty leaet for contact details).

Disposal

- This product contains a rechargeable lithium-ion

battery which must be disposed of properly.

- Contact your local town or city ocials for battery

disposal information. You can also call 1-888-224-

9764 or visit www.call2recycle.ca for battery

drop-o locations.

- For assistance, visit our website

www.philips.com/support or call 1-866-800-

9311 toll free.

- Your product is designed and manufactured with

high quality materials and components, which can

be recycled and reused. For recycling information,

please contact your local waste management

facilities or visit: www.recycle.philips.com.

Full Two-Year Warranty

Philips Electronics Ltd (Canada) warrants this new

product against defects in materials or workmanship

for a period of two years from the date of purchase,

and agrees to repair or replace any defective product

without charge.

IMPORTANT: This warranty does not cover damage

resulting from accident, misuse or abuse, lack of

reasonable care, the axing of any attachment

not provided with the product or loss of parts or

subjecting the product to any but the specied

voltage.*

NO RESPONSIBILITY IS ASSUMED FOR ANY

SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES.

Cutting units and combs are not covered by the terms

of this warranty because they are subject to wear and

tear.

In order to obtain warranty service, simply go to

www.philips.com/support for assistance. It is

suggested that for your protection you return

shipments of product by insured mail, insurance

prepaid. Damage occurring during shipment is not

covered by this warranty. NOTE: No other warranty,

written or oral, is authorized by Philips Electronics

Ltd. This warranty gives you specic legal rights, and

you may also have other rights which vary from state

to state, province to province or country to country.

Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above

exclusion and limitations may not apply to you.

*Read enclosed instructions carefully.

BT5775

BT5785

BT7665

Model

BTXXXX

10.4 mm - 20 mm

1 mm - 5 mm 5 mm - 1 mm

0.4 mm - 10 mm

BT5785

BT7665

BT5785

BT7665

7 8

12 13

English

IMPORTANT SAFETY INSTRUCTIONS

When using an electric product, basic precautions

should always be followed, including the following:

Read all instructions before using this product.

DANGER

To reduce the risk of electric shock:

- To charge the product, only use a USB power

source on a certied product with output

rating 5V, ≥ 1A. For safe charging in a moist

environment (e.g. in a bathroom), only use an

IPX4 (splash-proof) power source. A suitable

power source (e.g. Philips HQ87) is available via

www.philips.com/support. If you need support

nding the correct USB power source, contact

Philips support at 1-866-800-9311. Using a non-

certied USB power source may cause hazards or

serious injuries.

- Keep the USB cable, the USB power source and the

charging stand (if provided) dry.

- Do not reach for a corded product that has fallen

into water. Unplug immediately from the power

outlet.

- Do not place or store the product where it can

fall or be pulled into a tub or sink. Do not place or

drop the product into water or other liquid.

- This product does not work while it is connected

to the power outlet. Except when charging, always

unplug this product from the power outlet.

- Remove USB power source from power outlet and

product before cleaning the product with water.

WARNING

To reduce the risk of burns, re, electric shock, or

injury to persons:

- This product is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

3000.135.0846.x_XENON_BT5 BT7_DFU-CANADA_LFLT_foldedA7_BW.indd 1-63000.135.0846.x_XENON_BT5 BT7_DFU-CANADA_LFLT_foldedA7_BW.indd 1-6 07-03-2025 14:4107-03-2025 14:41

Bekijk gratis de handleiding van Philips BT7665, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.