Handleiding
Je bekijkt pagina 66 van 80
input signal might be poor. A weak digital signal is seen
as a picture that is breaking up in square blocks and
freezes occasionally. Much sooner than a bad analogue
signal, a bad digital signal will fall away.
• Check if the antenna cable is properly connected.
• Large loudspeakers, unearthed audio devices, neon
lights, high buildings and other large objects can
influence reception quality when you are using an
antenna. Try to improve the reception by changing the
antenna direction or moving devices away from the
TV. Bad weather might deteriorate the reception.
• Check if all connections, to and from your devices, are
properly connected.
• If reception on only one channel is poor, fine-tune this
channel with Analogue: manual installation. (Only for
analogue channels)
• Check if the incoming digital signal is sufficiently
strong. While watching a digital channel, press
OPTIONS and select Status and press OK. Check
the Signal strength and Signal quality.
Poor picture from a device
• Make sure that the device is connected properly.
Make sure that the device's output video setting is the
highest possible resolution if applicable.
• Restore picture style or change to another picture
style.
Picture settings change after a while
Make sure that Location is set to Home. You can
change and save settings in this mode.
(Home) > Settings > General settings > Location
A banner appears
If an on screen promotion banner appears occasionally
or the Picture style automatically switches back to Vivid
at startup, the TV is in Shop location. Set the TV to
Home location for use at home.
(Home) > Settings > General settings > Location
Picture does not fit the screen / Wrong or unstable
picture size / Picture position is incorrect
• If the picture size - its aspect ratio - does not fit the
screen, with black bars on the top and bottom or left
and right side of the screen, press (Home) >
Settings > Picture > Picture Format > Fill screen.
• If the picture size changes all the
time, press (Home) > Settings > Picture > Picture
Format > Fit to screen.
• If the position of the picture is incorrect on the screen,
try to check the signal resolution and output type of the
connected device, press (Home) > Settings
> Picture > Picture Format > Original.
Computer picture is not stable
Make sure that your PC uses the supported resolution
and refresh rate.
22.7. Sound
No sound or poor sound quality
• Check if the sound settings of the TV are OK, press
the volume or mute key.
• If you use a digital receiver (set-top box), check if the
volume on this receiver is not set to zero or mute.
• Check if the TV - the audio signal - is properly
connected with the Home Theatre System, if you use
such a system for the TV sound. Check if you connected
the HDMI cable to an HDMI ARC/eARC connection on
the Home Theatre System.
• Make sure that the TV audio output is connected to
the audio input on the Home Theatre System.
Sound should be heard from the HTS (Home Theatre
System) speakers.
Sound with loud noise
If you watch a video from a plugged in USB flash drive
or connected computer, the sound from your Home
Theatre System might be distorted. This noise is heard
when the audio or video file has DTS sound but the
Home Theatre System has no DTS sound processing.
You can fix this by setting the Digital out format of the
TV to Stereo.
Press (Home) > Settings
> Sound > Advanced > Digital out format
22.8. HDMI - UHD
HDMI
• Note that HDCP (High-bandwidth Digital Content
Protection) support can delay the time taken for a TV to
display content from an HDMI device.
• If the TV does not recognise the HDMI device and no
picture is displayed, switch the source from one device
to another and back again.
• This is an Ultra HD TV. Some older devices - connected
with HDMI - do not recognise an Ultra HD TV
electronically and might not work correctly or show
distorted picture or sound. To avoid the malfunctioning
of such a device, you can set the signal quality to a level
the device can handle. If the device is not using Ultra
HD signals, you can switch off Ultra HD for this HDMI
connection.
If the picture and sound of a device connected with
HDMI is distorted, check if a different HDMI Ultra
HD setting can solve this problem. You can check on
Help > User manual > General Settings > HDMI Ultra
HD.
• If there are intermittent sound disruptions, make sure
that output settings from the HDMI device are correct.
HDMI EasyLink does not work
66
Bekijk gratis de handleiding van Philips 43PUS8560, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Philips |
| Model | 43PUS8560 |
| Categorie | Televisie |
| Taal | Nederlands |
| Grootte | 8816 MB |
