Parmco WM10WF03 handleiding
Handleiding
Je bekijkt pagina 19 van 21
Cleanness and Maintenance
Use pointed nose pliers to withdraw the plastic filter. Clean, put back
and secure. These filter should be checked every 6 months or so, or
more often if there are frequent interruptions to the water supply.
The filter should be cleaned every 2 months or when there is fault that the “E03” is on
the screen.
Cleaning the drawer housing
Use a bottle brush to remove detergent residues inside the drawer
housing.
The filter must be put back in place after cleaning.
Important:
If the machine is exposed to temperatures below 0°C, certain precautions should be taken.
1. Turn off the water tap.
2. Unscrew the inlet hose.
3. Unhook the drain hose from the rear support and position the end of this hose and that of the
inlet hose in a bowl. Run the spin programme.
4. Disconnect the appliance.
5. Screw the inlet hose and reposition the drain hose.
6. When you intend to start the machine up again, make sure that the room temperature is
above 0°C.
Cleaning the water inlet filter
Cleaning the drain pump filter
After use
1. Disconnect the machine from
the mains electricity supply and
open the lower cover with a
screwdriver.
2. Place a container under the pump.
Unscrew and remove the filter.
3. Clean the filter carefully.
Troubleshooting guide
Difficult explanation
1. Check the connection and ensure
it is secure.
2. Change the temperature sensor.
1. The connection between the
temperature sensor and wire is
not secure.
2. The temperature sensor is
damaged.
1. Check the connection and ensure
it is secure.
2. Change the heating tube.
1. The connection between the
heating tube and wire is not
secure.
2. The heating tube is damaged.
1. Check the connection and ensure
it is secure.
2. Check if the machine is overloaded.
Switch off the machine, and retry
when the motor becomes cool.
3. Change the motor.
1. The connection between the
motor and wire is not secure.
2. The motor is protected
because of over-heat.
3. The motor is damaged.
1. Change the water inlet.
2. Check the connection and ensure
it is secure.
3. Change the water sensor.
1. The water inlet valve is damaged.
2. The connection between the water
sensor and wire is not secure.
3. The water sensor is damaged.
There is a Door
lock alarm.
The machine
fills overtime.
1. The water tap is not open.
2. The drain hose is put down.
3. The water inlet valve is damaged.
1. Open the water tap.
2. hook up the hose.
3. Change the water inlet valve.
“E01” is on
the screen.
The machine
drains overtime.
Water overflows
the machine.
/ Water sensor
works abnormal.
The motor does
not work.
There is a
heating tube
fault.
There is a
temperature
sensor fault.
1. Check the drain hose.
2. Clean the filter.
3. Check the drainage system and
clean it.
1. The drain hose is squashed
or kinked.
2. The drain pump filter is block.
3. The drainage system pipes
are blocked.
1. Lock the door well.
2. Put the garment into the drum.
3. Change the door lock.
1. The door is not locked well.
2. garment is caught between the
door and the seal.
3. The door lock is damaged.
“E02” is on
the screen.
“E04” is on
the screen.
“E03” is on
the screen.
“E05” is on
the screen.
“E06” is on
the screen.
“E07” is on
the screen.
Possible Cause
Problem
Error Code
Bekijk gratis de handleiding van Parmco WM10WF03, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Parmco |
| Model | WM10WF03 |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 1767 MB |
