Handleiding
Je bekijkt pagina 20 van 24
20
English
FAQs
Before requesting service or assistance, please follow
these simple guides to solve the problem.
≥ For details, refer to [eHELP] (Support > FAQs).
The TV does not switch on
≥ Check the mains lead is plugged into the TV and the
mains socket.
The TV goes into Standby mode
≥ Auto power standby function is activated.
The remote control does not work or is intermittent
≥ Are the batteries installed correctly? (p. 16)
≥ Has the TV been switched on?
≥ The batteries may be running low. Replace them with
new ones.
≥ Operation of the remote control is not possible due to
system startup when the LED is blinking orange. You
can use the remote control after the LED turns
constant red.
≥ Point the remote control directly at the TV’s remote
control signal receiver (within about 7 m and a
30 degree angle of the signal receiver).*
≥ Situate the TV away from sunshine or other sources of
bright light so they do not shine on the TV’s remote
control signal receiver.*
≥ If you are trying to use voice controls, is the remote
control registered (paired) with the TV? (p. 13)
When infrared communication is used
No image is displayed
≥ Check the TV is turned on.
≥ Check the mains lead is plugged into the TV and the
mains socket.
≥ Check the correct input mode is selected.
≥
Check the input mode in the input selection list to match
the signal being output by the external equipment.
≥ Is [Backlight], [Brightness], [Contrast] or [Colour] in the
Picture menu set to the minimum?
≥ Check all required cables and connections are firmly
in place.
An unusual image is displayed
≥ This TV has a built-in Self Test. Makes a diagnosis of
picture or sound problems.
[TV self test] (Settings > Device Preferences >
About)
≥ Turn the TV off with Mains power On / Off switch, then
turn it on again.
≥ If the problem persists, initialise all settings.
[Reset] (Settings > Device Preferences > About)
The image or sound from external equipment are
unusual when the equipment is connected via HDMI
≥ Set [HDMI Auto Setting] (Settings > Device
Preferences > Inputs) to [Mode1]. (p. 12)
No sound is produced from the connected HDMI
equipment
≥ Set the audio output format of the connected HDMI
equipment to PCM.
Voice control function does not work
≥ If the remote control is not registered (paired) with the
TV, register (pair) the remote control. (p. 13)
≥ Check the network connections and settings.
Parts of the TV become hot
≥ Parts of the TV may become hot. These temperature
rises do not pose any problems in terms of
performance or quality.
When pushed with a finger, the display panel moves
slightly and makes a noise
≥ There is a little gap around the panel to prevent
damage to the panel. This is not a malfunction.
About the inquiry
≥ Please contact your local Panasonic dealer for
assistance.
If you make an inquiry from a place where this TV is
not present, we cannot answer about contents that
require visual confirmation for connection,
phenomenon, etc. of this TV itself.
TH-40_50_58_65JX700GKST_Eng_8A06B00034100.book 20 ページ ２０２１年２月１９日 金曜日 午後４時５３分
Bekijk gratis de handleiding van Panasonic TH-50JX700K, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Panasonic |
| Model | TH-50JX700K |
| Categorie | Televisie |
| Taal | Nederlands |
| Grootte | 2506 MB |
