Panasonic DP-001-P handleiding
Handleiding
Je bekijkt pagina 9 van 12
9
DP-0
PRECAUTIONS FOR PROPER USE
• Never use this product as a sensing device for
personnel protection.
• In case of using sensing devices for personnel
protection, use products which meet laws and
standards, such as OSHA, ANSI or IEC etc., for
personnel protection applicable in each region or
country.
• This product is used for noncorrosive gas. The
product shall not be used for liquid or corrosive
gas. Never use uids having inammability,
toxicity, etc., that affect the human body, either.
Part description
Connecting
connector
Pressure port
(M5 female thread)
Mode
selection key
Digital display unit
Setting value DOWN key
Setting value UP key
OVER mark
OFF mark
ON mark
Key lock mark
Piping
• When using this product, connect a joint available in the market
to the pressure port. At the time, the tightening torque should be
1.0 N·m or less.
Mounting
• Use sensor mounting bracket MS-DP1-1 prepared independently.
When mounting this product with sensor mounting bracket, etc.,
the tightening torque should be 0.5 N·m or less.
M3 (length 6 mm 0.236 in)
screws with washers
(Accessory with MS-DP1-1)
Sensor mounting
bracket
MS-DP1-1
(Optional)
• Panel ttings MS-DP1-8 (optional) and front cover MS-DP1-3
(optional) are available.
• For the method for mounting panel ttings, refer to the instruction
manual that came with the MS-DP1-8.
Wiring
• Make sure that the power supply is OFF while performing the
wiring operation.
• Verify that the supply voltage variation is within the rating.
• If power is supplied from a commercial switching regulator,
ensure that the frame ground (F.G.) terminal of the power supply
is connected to an actual ground.
• In case noise generating equipment (switching regulator, inverter
motor, etc.) is used in the vicinity of this product, connect the
frame ground (F.G.) terminal of the equipment to an actual
ground.
• When extending the cable, use a cable whose conductor cross-
sectional area is 0.3 mm
2
or more. The cable can be extended to
up to 10 m 32.808 ft in total length.
• Do not run the wires together with high-voltage lines or power
lines or put them in the same raceway. This can cause
malfunction due to induction.
• Do not apply stress directly to the connection cable leader or to
the connector.
Connection
How to connect
• Insert the cable with connector
CN-14A(-R)-C□ into this product’s
connection connector section as shown
in the right gure.
How to disconnect
• Pressing the release lever of the cable
with connector, pull out the connector.
Note: Do not pull by holding the cable without pressing the release lever, as
this can cause cable break or connector break.
Factory setting
Type Low pressure type High pressure type
Operation setting EASY mode
NO / NC setting NC NO
Threshold value −50.0 0.500
Pressure unit kPa MPa
Display color Red when ON, White when OFF
Response speed 2.5 ms
Error indication
Error indication
Description Remedy
The load is short-circuited
causing an overcurrent to
ow.
Turn OFF the power and
check the load.
Pressure is applied during
zero point adjustment.
Applied pressure at the
pressure port should be
brought to atmospheric
pressure and zero-point
adjustment should be done
again.
The applied pressure
exceeds the upper limit of
the displayed pressure
range.
Applied pressure range
should be brought within
the rated pressure range.
The applied pressure
exceeds the lower limit
(back pressure) of the
displayed pressure range.
When other error massage is displayed, contact us.
Others
• This product has been developed / produced for industrial use
only.
• The product shall be used only within the rated pressure range.
• Do not apply pressure exceeding the pressure resistance.
Otherwise, destruction of diaphragm occurs, preventing the
product to perform normal operation.
• Do not use during the initial transient time (0.5 sec.) after the
power supply is switched ON.
• The specication may not be satised in a strong magnetic eld.
• This product is suitable for indoor use only.
• Take care that strong impact such as fall is not given to this
product. Otherwise, it may be destroyed.
• Avoid dust, dirt, and steam.
• Take care that the product does not come into contact with
organic solvents such as thinner.
• Take care that the product does not come into contact with oil or
grease.
• Take care that the product does not come into contact with
strong acid or alkaline.
• Do not insert wire into the pressure port. Otherwise, destruction
of diaphragm occurs, preventing the product to perform normal
operation.
Release lever
Cable with connector
CN-14A
(
-R
)
-C□
Bekijk gratis de handleiding van Panasonic DP-001-P, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Panasonic |
| Model | DP-001-P |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6757 MB |
