Ozito PSVS-018 handleiding
Handleiding
Je bekijkt pagina 2 van 2
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. Sure Grip Handle
2. On/Off Switch
3. 2 Speed Vacuum Setting Button
4. Vacuum Head
5. Head Release Button
6. Dust Canister
7. Suction Tube Release Button
8. Suction Tube
9. Motorised Cleaning Head Release Button
10. Wheels
11. Motorised Cleaning Head
Fitting the Accessories
1. Fit the vacuum head into
the suction tube until it
latches in place with a
click.
2. Fit the motor brush into the
suction tube until it latches
in place with a click.
Note: The 2-in-1 crevice
nozzle with brush and
the exible crevice
nozzle can be mounted
either directly on the
vacuum head or on the
suction tube.
Fitting the Filters
1. Press the release button
and remove the dust
canister while doing so.
2. Then take the lter together
with the lter cage out
of the dust canister. The
lter must be taken out of
the lter cage for it to be
thoroughly cleaned.
Installing The Battery Pack
1. Slide the battery into the
tool base until it clicks into
place.
Removing The Battery Pack
1. Hold down the battery
release button.
2. Slide the battery out.
On/Off Switch
1. Press the button to switch
the tool on and press it
again to switch it off.
Modes
The vacuum has 2 speed settings:
ECO - Normal suction power
and motor brush speed for
cleaning hard oors and
short-pile carpets or when
a longer running time is
needed.
BOOST - High suction power
and motor brush speed for
cleaning plush carpets and
when a higher cleaning level
is needed.
Note: The equipment starts in BOOST mode. Press the vacuum setting
switch once to switch to ECO mode.
Suction Nozzles
1. Flexible crevice nozzle
The crevice nozzle is designed for vacuuming in corners, edges and other
areas that are difcult to access.
2. 2-in-1 crevice nozzle with
brush
The 2-in-1 crevice nozzle with
brush can be used as either
a crevice nozzle or a brush.
To use it as a brush, press
the button on the side of the
nozzle and push the brush
forward until it latches in
place.
Note: To achieve the best suction performance, empty the dust canister
each time after you use the cleaner or as soon as the dust reaches
the MAX line.
Fitting the Wall Holder
1. Align the wall holder
to the screws (2 plastic
wall plugs, and 2 screws
included) and x it to the
wall.
Note: The holder provides a practical
means of storing the stick vacuum
after use.
Fitting the Brush Roller
1. While pressing the release
button push it to the left
and hold it tight (a). Lift
the brush roller out of the
housing (b). Assemble in
reverse order.
Note: Make sure that the brush roller latches in place correctly.
This tool is compatible with all batteries & chargers from the Ozito PXC range.
CORDLESS STICK VACUUM
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. FITTING THE BATTERY
3. CONTROLS 4.USAGE2. ASSEMBLY
SETUP & PREPARATION OPERATION
a) b)
2
4
6
1
3
5
7
8
9
11
10
12 13 15
16 17 18
19
20
14
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
WARNING! DO NOT PUT HAND OR FINGERS NEAR
MOTORIZED CLEANING HEAD WHILE VACUUM IS
RUNNING.
PSVS-018
ACCESSORIES
WARNING! MAKE SURE THAT NOTHING IS JAMMED
BETWEEN THE EQUIPMENT CONNECTIONS.
WARNING! NEVER USE THE EQUIPMENT WITHOUT
FILTERS ALWAYS MAKE SURE THAT THE FILTERS
ARE SECURELY SEATED!
12. Wall Holder
13. Plastic Wall Plug (for masonry or timber wall x2
14. Screws x2
15. Flexible Crevice Nozzle
16. 2-in-1 Crevice Nozzle With Brush
17. Filter
18. Filter Cage
19. Brush Roller Release Button
20. Brush Roller
Bekijk gratis de handleiding van Ozito PSVS-018, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ozito |
| Model | PSVS-018 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 1003 MB |