Optimate Lithium 5A handleiding
Handleiding
Je bekijkt pagina 6 van 44
6
CHARGE PROGRAM
Protection
BMS reset
2
1
Charger will not proceed without user interaction.
LED #2 REVERSE POLARITY: Lights when the battery connections
are incorrect. The charger is electronically protected so no damage will
result, and the output will remain disabled until the connections are
corrected.
BMS RESET: for batteries with a battery management system (BMS) that
protects against deep discharge. Disconnect the charger from mains supply.
Wait for LED #1a/1b to go out. Reconnect to mains supply. A special BMS
reset pulse is delivered for up to 5 seconds. The program should continue to
STEP 4.
STEP 1
Low Volt Start
≥ 0.5V
V
Battery voltage check - OptiMate Lithium automatically activates
if connected battery voltage is at least 0.5 Volt.
STEP 2
TEST before
charge
STEP 3
Temperature
check
TEST LEDs
6 : GREEN
7 : YELLOW
8 : RED
TEST
8
7
6
TEST LEDs #6/7/8 indicate the battery condition prior to charging. Consult the
table on page 2 to match TEST LED indication to an estimated state of
charge percentage (SOC%).
During the test:
OPTIMIZE minimum charge time is set according to the test result, varying
between 10 minutes for a battery with 80% or higher state of charge to 120
minutes
for a battery with 40% or less state of charge.
Ambient temperature is measured to determine charge voltage parameters.
LOW TEMPERATURE WARNING - LED #8 (red) flashing: The temperature
measured at OptiMate Lithium is below -20 degrees Celcius or 4 degrees
Fahernheit, below the safe charging AND discharging zone for LiFePO
4
batteries.
Charging commences after 10 seconds.
8
7
6
90 100%603010%
13.3V 13.6V+ 13.13V13.00V12.80VV
8
7
7
6
0
0.5V
STEP 4
ULTRA LOW
VOLT SAVE
STEP 5
LOW VOLT SAVE
STEP 6
TEST - cell
damage
LED #3 : RED
3
IMPORTANT: If this mode engages read the section VERY FLAT
NEGLECTED BATTERIES on the preceding page.
This mode engages
if the battery was more than 90% discharged / voltage
is below 12.8V safeTº: Charge current is automatically adjusted according
to voltage and ambient temperature measured during the test.
VERY LOW VOLTAGE SAVE for batteries between 0.6V and 8.8V :
Current starts at 125mA and will increase to 325mA depending on charge
progress. If the voltage did not rise above 8.8V within 2 hours, charging will
be suspended and the TEST LED #8 (red) will flash, indicating the battery
may have suffered permanent damage or a professional assessment is
required.
LOW VOLTAGE SAVE for batteries between 8.9V and 12.8V (16V):
Maximum current is set to 1.25A. The battery's charge acceptance is
monitored for unusual behaviour.
A healthy LiFePO
4
battery will progress to CHARGE mode within 4 hours,
otherwise charging will be suspended and TEST LED #8 (red) will flash,
indicating the battery may have suffered permanent damage or a
professional assessment is required.
10
OptiMate
maintenance
9
TEST after
CHARGE
1
Low Volt
Start (0.5V)
2
TEST before
charge
3
Temperature
check
4
Ultra LOW
VOLT SAVE
5
LOW VOLT
SAVE /
cellmonitoring
6
TEST -
cell damage
7
Cell-balancing
CHARGE
8
OPTIMIZE
Bekijk gratis de handleiding van Optimate Lithium 5A, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Optimate |
| Model | Lithium 5A |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6090 MB |
