Omnitronic VFM 210 MK2 handleiding
Handleiding
Je bekijkt pagina 9 van 12
9
•
EN
3
Setup
The speaker systems can be placed as desired or mounted onto stands or distance tubes with a standard
tube diameter of 35 mm.
General notes
• The location must be solid, plane, anti-slip, vibration-
free, oscillation-free, and fire-resistant. The
installation area must hold a minimum point load of
5 times the system's load (e.g. weight 20 kg - point
load 100 kg). The speakers must never be installed
higher than 100 cm without secondary attachment.
• Always install the speaker systems in a way that a
minimum distance of three meters to the audience is
kept. This is the only way to avoid hearing damage for
unreasonable listeners. Block the area in front of the
speaker systems with appropriate means.
• Extreme levels like feedback, bass-hum or the beats
of a dropping microphone can destroy the
loudspeakers within very short time and produce
immediate hearing damage. Such extreme levels
must be avoided at any rate. We recommend using
appropriate equalizers and compressors/limiters.
• For transport, the speaker systems feature two
carrying handles. The speaker system should be
carried without force by two persons of the same size.
Carrying the speaker system as one person alone
should be avoided as the high weight and the strain
could lead to back damages and torsions. Please
note that all speaker systems with more than 25 kg
weight must be transported with two persons.
Installation on a wall mounting
• When installed on a wall mounting, the speaker
system must always be secured with a safety bond.
Before attaching the speaker system, make sure that
the installation area can hold a minimum point load of
10 times the installation's weight (e.g. 13 kg weight -
130 kg point load).
• The durability of the installation depends very much
on the material used at the installation area (building
material) such as wood, concrete, gas concrete, brick
etc. This is why the fixing material must be chosen to
suit the wall material. Always ask a specialist for the
correct plug/screw combination indicating the
maximum load and the building material.
Stands
• Stands must only be installed on a plane area with a
maximum inclination angle of 5°.
• When using stands or satellite systems under the
influence of horizontal forces, e.g. through wind, the
standing safety can be impaired. This is why
additional safety measures like attaching ballast
weights have to be taken.
• If inclined tension cables or prolonged outriggers are
used, the area of danger has to be marked or even be
blocked.
• Before lifting or lowering the telescopic tubes, you
must always block a safety area around the stand or
satellite system. This safety area must have a
diameter of 1.5 times the maximum height.
• Lifted telescopic tubes always have to be secured
with a secondary securing!
• The total weight of the installation (=total weight of all
individual parts) must never exceed the maximum
load of the installation area.
• The stand has to be installed out of the reach of
people.
• An unintended movement of the load has to be
avoided - also in case of fire!
• The installer is responsible for adhering to the
carrying capacity given by the manufacturer, the
safety requirements and the qualification of possible
co-workers.
• When people are located below the load, all
necessary safety measures have to be taken in order
to avoid injury.
• The personnel have to be instructed on the content of
the user manual and on the dangers related with
operating stands.
• Depending upon the individual installation spot, all
necessary measures against movement and for
securing the standing safety have to be created.
• The installation is only allowed on carrying areas. In
some cases, an appropriate substructure, e.g. via a
balancing foot, has to be created. When choosing the
installation material, optimum dimensions have to be
chosen in order to secure maximum safety.
•
Speaker systems installed on stands or satellite
systems may cause severe injuries when crashing! If
installing on slippery surfaces, the legs must be
secured with screws or nails via the provided holes or
an anti-slippery mat has to be used.
Bekijk gratis de handleiding van Omnitronic VFM 210 MK2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Omnitronic |
| Model | VFM 210 MK2 |
| Categorie | Speaker |
| Taal | Nederlands |
| Grootte | 2827 MB |
