Numatic HFM1523 handleiding
Handleiding
Je bekijkt pagina 8 van 36
8
8
COMPONENT INTERVAL INSPECT FOR
Mains Lead DAILY Scuffi ng, cracks, splits, conductors showing
Pads/Brushes BEFORE EACH USE Damage, wear, drive collar wear
Handle and Deck BEFORE EACH USE Wear, cracks, splits
As with all electrical equipment care and attention must be exercised at all times during its use, in addition to ensuring that
routine and preventative maintenance is carried out periodically in order to ensure its safe operation. Operators shall be
adequately instructed as to the correct use of the machine.
Failure to carry out maintenance as necessary, including the replacement of parts to the correct standard
could render this equipment unsafe and the manufacturer can accept no responsibility or liability in this respect.
When ordering spare parts always quote the Model Number / Serial Number specifi ed on the Rating Plate.
Do not use on cleaning surfaces having a gradient exceeding that marked on the machine. While on ramps or inclines, avoid sudden
stops. Avoid sharp turns. Use low speed down ramps. Clean only while descending (driving down) the ramp.
This machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge. Children should be supervised to ensure that they do not play with the appliance.
Only use brushes provided with the appliance or those specifi ed in the instruction manual.
The use of other brushes may impair safety.
A full range of brushes and accessories are available for this product.
Only use brushes or pads which are suitable for the correct operation of the machine for the specifi c task being performed.
It is essential that this equipment is correctly assembled and operated in accordance with current safety regulations.
When using the equipment always ensure that all necessary precautions are taken to guarantee the safety of the operator and
any other persons who may be a ected.
Wear nonslip footwear when scrubbing. Use a respiratory mask in dusty environments.
When cleaning, servicing or maintaining the machine, replacing parts or converting to another function the power source shall be switched o .
Mains operated machines shall be disconnected by removing the power plug, and battery operated machines shall be disconnected by
using top ON/OFF button on the battery.
Machines left unattended shall be secured against unintentional movement.
When detergents or other liquids are used, read the manufacturer’s instructions.
Do not allow the supply cord to come into contact with the rotating brushes or pads.
This machine is not suitable for picking up hazardous dust
This machine shall be stored indoors only
This machine is for indoor use only.
NOTES: This machine is intended for commercial use, for example in hotels, schools, hospitals, factories, shops, offi ces
and rental businesses. This Product meets the requirements of IEC 60335 - 2-67
• Ensure only competent persons unpack/assemble the machine.
• Keep your machine clean.
• Keep your brushes in good condition.
• Replace any worn or damaged parts immediately.
• Regularly examine the power cord for damage, such as cracking or ageing. If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a hazard.
• Only replace the power cord with the correct Numatic approved replacement parts.
• Ensure that the work area is clear of obstructions and / or people.
• Ensure that the working area is well illuminated.
• Pre-sweep the area to be cleaned.
• Use steam cleaners or pressure washers to clean the machine or use in the rain.
• Attempt machine maintenance or cleaning unless the power plug has been removed from the supply outlet.
• Allow any inexperienced repairs. Call the experts.
• Strain cable or try to unplug by pulling on cable.
• Leave the brush pad on the machine when not in use.
• Allow the machine to be used by inexperienced or unauthorised operators or without appropriate training.
• Expect the machine to provide trouble-free, reliable operation unless maintained correctly.
• Run the machine over power cable during operation.
• Lift or pull the machine by any of the operating triggers, use the main handle.
• Remove the handle from the machine except for service and repair.
WARNING
CAUTION
DO
DON’T
Information for Floor Machine
READ MANUAL BEFORE USE
EN
Bekijk gratis de handleiding van Numatic HFM1523, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Numatic |
| Model | HFM1523 |
| Categorie | Boenmachine |
| Taal | Nederlands |
| Grootte | 7782 MB |
