Nord Stage 4 handleiding
Handleiding
Je bekijkt pagina 59 van 76
11. MENUS | 59
PEDAL MENU
Hold SHIFT and press PEDAL (Program 6) to access the Pedal menu.
Use the PAGE 3 and 4 buttons to navigate between pages. The
PROGRAM dial is used to change settings, and soft buttons to access
additional settings (as described above), where applicable. Press EXIT
(Shift) to leave the menu.
1 - CONTROL PEDAL
TYPE
The Nord Stage 4 accepts many commonly available expression pedals
through its CONTROL PEDAL input. Choose a setting that matches the
pedal being used.
Range: Roland (default), Yamaha, Korg, Fatar (and Studiologic),
Nord SP-2
l If a connected pedal is operated while this menu page is open, a
percentage is displayed which can be used to determine the range
of the connected pedal. This can be helpful when finding a suitable
setting for a pedal that is not explicitly supported.
FUNC (FUNCTION)
This setting determines the functionality of a pedal that is attached to
the Control Pedal input. The two settings are Control (to use the pedal
with the Morph functionality) and Ctrl + Swell (combines Morph control
and Organ Swell).
Range: Control (Default), Ctrl + Swell
GAIN
This setting allows for adding gain to the pedal output. This can be
useful if an attached pedal does not reach its maximum level or setting.
Range: 1 - 10
2 - SWELL PEDAL
TYPE
This setting configures a pedal attached to the ORGAN SWELL jack. See
“Ctrl Pedal Type” above for details.
Range: Roland (default), Yamaha, Korg, Fatar (and Studiologic)
FUNC (FUNCTION)
This setting configure the Swell Pedal destination. Set this to Swell if you
want this pedal to act as a Swell pedal for the organ, or to Volume if it
should control the volume of all the Nord Stage 4 sound engines. When
set to Wheel Morph, the Swell Pedal mirrors the Morph functionality of
the Modulation Wheel.
Range: Swell (Default), Volume, Wheel Morph
GAIN
This setting allows you to add some gain to the output of the pedal. This
can be used if an attached pedal does not reach the maximum level or
setting.
Range: 1 - 10
3 - SUSTAIN PEDAL
TYPE
This setting needs to correspond to the type of pedal connected to the
SUSTAIN PEDAL jack for the sustain functions to work correctly.
Depending on the selected Type, one or three vertical bars
(corresponding to a single and a triple pedal respectively) are shown in
the display, which will fill up as pedals are pressed down – indicating that
a pedal has been properly connected.
The Nord SP-1, Normally Open and Normally Closed settings
correspond to basic, on-off type, pedals whereas the Nord SP-2 pedal
is of a continuous type which, like the Triple Pedals, is compatible with
the Pedal Noise and half damping features. The Nord TP-1 setting
corresponds to the legacy Nord Triple Pedal 1. The Nord Triple Pedal
2 is attached to a dedicated 5-pin jack and is not affected by settings
made on this menu page.
Range: Nord SP-1 (Nord Single Pedal 1, default), Nord SP-2 (Nord
Single Pedal 2), Nord TP-1 (Nord Triple Pedal 1), Normally Open,
Normally Closed
FUNC (FUNCTION)
If desired the Sustain Pedal can also alter the speed of the Rotary
Speaker effect by setting its Function to either Sus+Rotor Hold or
Sus+Rotor Toggle.
Range: Sustain (Default), Sus+Rotor Hold, Sus+Rotor Toggle
4 - TRIPLE PEDAL FUNCTION
A connected Triple Pedal, whether its a Nord Triple Pedal 1 connected
to the Sustain Pedal jack or a Nord Triple Pedal 2 connected to the
Triple Pedal jack, can be set up in a variety of ways for controlling a
number of different features. The Right pedal always controls Sustain (or
optionally Sustain+Rotor Hold/Rotor Toggle), while the Left and Middle
pedals can each control a larger selection of parameters.
ABOUT THE “USER ASSIGNED” SETTING
When set to “User Assigned” the Left or Middle pedal is used for these
functions, as active on the Nord Stage 4 panel:
• Mst Clk Pedal Tempo Tap
• Layer Scene II Pedal
• Synth Vibrato Pedal
• Pump effect in Ped mode
RANGE
Range Left: Una Corda (Default), User Assigned, Layer Scene Hold,
Layer Scene Toggle, Pump, Mst Clk Tap, Synth Vibrato, Program Up,
Program Down, Rotor Hold, Rotor Toggle
Range Middle: Sostenuto (Default), User Assigned, Layer Scene Hold,
Layer Scene Toggle, Pump, Mst Clk Tap, Synth Vibrato, Program Up,
Program Down, Rotor Hold, Rotor Toggle
Range Right: Sustain (Default), Sus+Rotor Hold, Sus+Rotor Toggle
Bekijk gratis de handleiding van Nord Stage 4, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Nord |
| Model | Stage 4 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10906 MB |
