Nord Modular G2 handleiding
Handleiding
Je bekijkt pagina 23 van 291
NORD MODULAR G2 V1.4x 2. Synth quick tour: Check out some Performances
Page 23
internal memory banks, tweak the parameters knobs and check out different Variations as described
above.
Note that to be able to load individual Patches the Performance Mode
LED
should be
OFF
.
CHECK OUT SOME PERFORMANCES
A Performance is a combination of up to four Slots. See
also “Playing multitimbrally” on page 18 and
“Performances” on page 18.
Enter Performance mode by pressing the
P
ERFORMANCE
M
ODE
button (button
LED
lights
up). Load a Performance into the Slots by first turning
the R
OTARY
D
IAL
to select the Performance, then
press the P
ATCH
L
OAD
button to load and activate the
Performance for play. As you can see, several S
LOT
LEDS
are now lit to indicate that several Patches are used in the Performance. The Performance name is
shown in the M
AIN
D
ISPLAY
and the first 8 parameters of the focused Patch are shown in the
A
SSIGNABLE
D
ISPLAYS
.
Note that a Performance always loads in all four Slots, storing any previously loaded Patches in the Slots
in a temporary buffer, so changing back to Patch mode will reload those previously loaded Patches before
Performance mode was activated. Also note that in the loaded Performance not all Slots need to be
active. If a Slot
LED
does not light up it simply indicates that this Slot is inactive.
A
CCESS
ASSIGNED
P
ERFORMANCE
(G
LOBAL
)
PARAMETERS
Each Performance can have a separate set of G
LOBAL
P
ARAMETER
P
AGES
, in addition to the Parameter
Pages of each Patch in the Performance. See also
“Parameter pages” on page 19 and “Global
(Performance) Parameter Pages” on page 49.
Hold down S
HIFT
and press the P
ATCH
S
ETTINGS
button to access G
LOBAL
P
ARAMETER
P
AGE
A1.
Alternatively you can ‘double click’ the P
ATCH
S
ETTINGS
button. Now, 8 new parameters are shown
in the A
SSIGNABLE
D
ISPLAYS
and you can edit them.
If you go to the P
AGE
A2, another 8 Performance
parameters are displayed, and so on. If you want to access the Programmable Parameter Pages of each
individual Patch, hold down S
HIFT
and press the P
ATCH
S
ETTINGS
button again. Alternatively you can
‘double click’ the P
ATCH
S
ETTINGS
button. Now, the first Parameter Page of the Patch in the focused
Slot is shown in the A
SSIGNABLE
D
ISPLAYS
.
This means that a total of 600 knob assignments can be stored in a Performance, 120 for each Slot plus
and extra 120 in the Global pages. The assignments in the Global pages can be a mix of module knob
assignments from all four Slots. Note that globally assigned knobs do not have to be previously assigned
in the individual Slot pages themselves.
1:1
Welcome
OSC1------------|
Freq Fine
OSC2-------
Freq
-
--------|
Release
A:Filter2-------|
Freq Res
B:OSC2----------|
Freq Fine
Bekijk gratis de handleiding van Nord Modular G2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Nord |
| Model | Modular G2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 60689 MB |
