Handleiding
Je bekijkt pagina 5 van 38
13. The heater must not be located immediately below a wall
socket.
14. Do not connect the fan heater using an on/off timer or other
equipment which can automatically switch the device on.
15. The heater must not be placed in rooms where flammable
liquids or gases are used or stored.
16. If an extension cord is used, it must be as short as possible and
always be fully extended.
17. Do not use this heater in the immediate surroundings of a bath,
a shower or a swimming pool.
18. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
19. You must not connect other appliances to the same mains
socket as the fan heater.
20. Make sure heater is always under surveillance and keep
children and animals away from it;
21. When you don’t use the appliance for a long time, unplug the
appliance. Don’t leave the heater for a considerable amount of
time when in use. Pull the plug straight out, never remove the
plug by pulling on the cord.
22. Keep the heater far from curtain or places where the air inlet can
easily be blocked.
23. Parts of the heater may exceed 200℃ , contact with the heating
tube, reflector, or mental parts near the heating tube, may cause
severe burns . To avoid burns, do not let bare skin touch hot
surface.
24. Always allow heating element to cool at least 10 minutes before
touching the heating tube or adjacent part
25. In order to prevent possible electric shock or leakage current,
never use the appliance with wet hand or operate the appliance
when there is water on the power cord.
26. Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities. Contact your local
government for information regarding the collection systems
available. If electrical appliance are disposed of in landfills or
dumps, hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and well-
being.
27. This appliance is not intended for use by persons (including
children) with reduces physical, sensory or mental capabilities
or lack of experience and knowledge unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
28. Children should be supervised to ensure that they do not play
with the appliance.
TECHNIACAL SPECIFICATIONS
Model
90-037
Waterproof class
IP 44
Voltage
230V ~
Required power
1500W
Current
6,5A
Required fuse
10A
Setting
1500W
Self-resetting thermostat
Yes
Heating area
6-7 m2
Max. lighting time
6000 h
Dimensions (mm)
425x425x180
Weight (kg)
1,7
INTRODUCTION
The infrared heaters produce instant and comfortable heat like the
sun. These robust and weatherproof heaters are designed for
domestic and commercial heating applications within indoor and
outdoor areas.
INSTALLATION
Important: Ensure that the supply cables is well mounted and that it
does not come into contact with reflector of the heater or that does
not trail into heated area.
1.This heater should be installed by a competent person, i.e. a
qualified electrician.
2.Always disconnected the heater from the electricity supply and
allow it to cool before installation.
3.This heater can be heat directly.
4.The supply cable must be at the lower end of the heater if the heater
is installed at an angle or vertically.
5.Keep the supply cord away from the body of the heater which will
get hot during use.
6.Do not install the heater on an inflammable surface.
7.Observe the minimum safe distance between the heater body and
the inflammable surfaces when mounted.
8.If the heater is to be used outside, a weatherproof outlet is
recommended.
9.Before drilling ensure that there are no wires or water pipes in the
area where the heater is to be installed.
10.The heater must be installed on the mounting brackets provided.
11.Fasten the brackets securely to the mounting surface and the
backside of the heater using the nuts and screws supplied.
12.Fasten the heater securely on the brackets using the nuts and
bolts supplied.
Installation steps:
1. Connect the chain and connecting ring with a carabiner.
2. Hang the chain on the rail and then lock it with a carabiner.
Requirements of Installation:
1.Keep 350 mm distance from heater to ceiling.
2. Keep at least 800 mm distance between heater and surrounding.
3. Keep at least 1800 mm height from heater to ground.
Bekijk gratis de handleiding van NEO Tools 90-037, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | NEO Tools |
| Model | 90-037 |
| Categorie | Heater |
| Taal | Nederlands |
| Grootte | 8055 MB |
