Handleiding
Je bekijkt pagina 6 van 57
13. The heater must not be located immediately below a wall
socket.
14. Do not connect the fan heater using an on/off timer or other
equipment which can automatically switch the device on.
15. The heater must not be placed in rooms where flammable
liquids or gases are used or stored.
16. If an extension cord is used, it must be as short as possible and
always be fully extended.
17. Do not use this heater in the immediate surroundings of a bath,
a shower or a swimming pool.
18. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
19. You must not connect other appliances to the same mains
socket as the fan heater.
20. Make sure heater is always under surveillance and keep
children and animals away from it;
21. When you don’t use the appliance for a long time, unplug the
appliance. Don’t leave the heater for a considerable amount of
time when in use. Pull the plug straight out, never remove the
plug by pulling on the cord.
22. Keep the heater far from curtain or places where the air inlet can
easily be blocked.
23. Parts of the heater may exceed 200℃ , contact with the heating
tube, reflector, or mental parts near the heating tube, may cause
severe burns . To avoid burns, do not let bare skin touch hot
surface.
24. Always allow heating element to cool at least 10 minutes before
touching the heating tube or adjacent part
25. In order to prevent possible electric shock or leakage current,
never use the appliance with wet hand or operate the appliance
when there is water on the power cord.
26. Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities. Contact your local
government for information regarding the collection systems
available. If electrical appliance are disposed of in landfills or
dumps, hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and well-
being.
27. This appliance is not intended for use by persons (including
children) with reduces physical, sensory or mental capabilities
or lack of experience and knowledge unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
28. Children should be supervised to ensure that they do not play
with the appliance.
TECHNIACAL SPECIFICATIONS
Model
90-031
Waterproof class
IP55
Voltage
230V ~
Required power
2000W
Current
9A
Required fuse
10A
Setting
2000W
Self-resetting thermostat
Yes
Heating area
18 m2
Max. lighting time
6000 h
Dimensions (mm)
575x110x110
Weight (kg)
1.3
INTRODUCTION
The infrared heater contains an HELEN LAMP formed reflector
heating system that provides even heat distribution. The infrared
heater saves 30% - 40% of electricity in comparison to traditional
heaters. The infrared heater is commonly used for indoor or outdoor
spot heating. Perfect for garages, outdoor patios, indoor pools or
workshops. The infrared heater is designed to heat an area of 18 m
2
.
The service life of the heating lamp is 6000 hours.
ASSEMBLY INSTRUCTIONS
INSTALATION ACCESSORIES
1
Bracket
L shape
4 PCS
2
Mounting pin
M6x60
4 PCS
3
Screw
M5x10
4 PCS
4
Nut
M6
2 PCS
5
Washer
6 mm x 1 mm
2 PCS
6
Screw
M6x12
2 PCS
INSTALLATION
Please check all the items against the parts list after opening the box.
Only all the items are complete, the installation could be followed.
1. Two brackets 1# should be attached to heater by screws 3#.
2. Drill holes and mount two brackets 1# by mounting pins 2#.
3. Connect brackets by bolts 5# and nuts 4#.
Tools needed: pencil, hammer, level, screw driver, power drill
and drill bits.
A wall mounting bracket is provide with the heater which has been
specifically designed to allow this product to be fitted to a wall or
ceiling before drilling the holders for the wall/ceiling is solid and that
there are no hidden water pipes or electric wires. The heater must be
installed no less than 40 cm form side walls and no less than 180 cm
off the floor.
Important: Ensure that the supply cables is well mounted and that it
does not come into contact with reflector of the heater or that is does
not trail into heated area, the supply cable can be fixed to them metal
mounting bracket behind heater with plastic zip ties.
Bekijk gratis de handleiding van NEO Tools 90-031, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | NEO Tools |
| Model | 90-031 |
| Categorie | Heater |
| Taal | Nederlands |
| Grootte | 16934 MB |
