MSW -POWER DRAIN CLEAN 2.3E handleiding

33 pagina's
PDF beschikbaar

Handleiding

Je bekijkt pagina 7 van 33
IV. SCOPE OF APPLICATION
The Drain Cleaning Machine is intended solely for clearing blocked pipes and outlets. It may be used
indoors and outdoors only in good weather conditions – it is prohibited to use the plunger in high tempe-
rature, as well as during rain-/snowfall.
The user is liable for any damage resulting from non-intended use of the device!
V. BEFORE FIRST USE
Upon receipt of the goods, check the packaging for integrity and open it. If the packaging is damaged, please
contact your transport company and distributor within 3 days, and document the damages as detailed as
possible. Do not turn the package upside down! When transporting the package, please ensure that it is
kept horizontal and stable.
VI. DISPOSING OF PACKAGING
Please keep all packaging materials (cardboard, plastic tapes and Styrofoam), so that in case of a problem,
the device can be sent back to the service centre in accurate condition!
VII. INSTALLING THE APPLIANCE
Positioning the machine
Place the device on a dry and stable surface, in vertical position, so that it wouldn’t move during work. The
foundation must be able to resist the weight of the device, it should be at and level. The device is to be
located in such a way that the mains plug was accessible at all times. Place the device about 20cm from the
opening of the cleared pipe. Remember for the mains supply to be compatible with the details specied on
the rating plate.
VIII MACHINE OPERATION - BASICS
MSW-DRAIN CLEAN 23E
Description of the device:
1
2
3
4
5
6
7
8
9
10
11
12
1. Motor switch:
FOR / REV – change of the coil rotation direction
OFF – device turned off
2. Belt guard
3. Belt
4. Residual current device GFCI
5. Wheels
6. Pedal
7. Drum
8. Coil
9. Outlet nozzle
10. Lever
11. Knob
12. Handle
DEVICE OPERATION DESCRIPTION – APPLICABLE TO MODEL MSW-DRAIN CLEAN 23E
Operation:
1. After receiving the device, assemble it as shown in the attached drawing. Before commencing
operation, ensure that neither the device nor the power cable are damaged. Next, make sure that the
switch at the motor is in the “OFF” position. If it is not, put it in the middle position.
2. When all the elements are in place, take the coil out of the drum and thread it through the outlet
nozzle. In order to do so, undo the black knob, thread appropriate length of the coil through the
nozzle opening and tighten the knob, so that the coil could perform its function when the engine is on.
Overtightening the knob will jam the coil in the device, and if the knob is too loose, the coil will not
be able to come out or retract. When the coil is ready, t an appropriate tip with the power supply
turned off. In order to attach the tip to the coil, undo the bolt located at the end of the coil, t the tip
and tighten the bolt, so that the tip was rmly attached to the coil.
3. Next, connect the device to the mains outlet. Every time before turning the device on, it must be
tested as follows: press the “RESET” button, turn the device on as per the following guidelines, and,
during operation, press the “TEST” button. If the device stops, it means that the GFCI switch works
properly and the device can be used safely. If the device fails to stop after pressing the TEST button,
immediately disconnect it from the power supply.
After the test, press the “RESET” button to operate the device normally. If during operation the
„RESET” button goes off automatically, or if it is impossible to turn it on, it means that the device
is most likely defective. In such a case, disconnect the device from mains immediately and follow the
instructions provided in the section “REGULAR INSPECTION OF THE DEVICE”.
4. In order to start clearing, place the device about 20 cm from the place of inserting the coil, insert the
coil into the opening in such a way that after insertion the coil does not twist and curl. Then, switch
the rotation direction switch located at the engine and put the lever in the appropriate position.
Possible settings:
Switch in the FOR position + lever in the upper position – the coil rotates clockwise and comes out.
Switch in the FOR position + lever in the lower position – the coil rotates clockwise and retracts.
Switch in the REV position + lever in the upper position – the coil rotates counter clockwise and
retracts.
Switch in the REV position + lever in the lower position – the coil rotates counter clockwise and
comes out.
Next, you can turn the device on using the pneumatic pedal provided with the device.
Always be ready to immediately stop the power device! Caution! The coil is about 23m long – it is not
recommended to remove impurities located near this distance.
5. In order to wind the coil in, set the lever and the switch in the appropriate position (as specied in
item 3 above) and press the pedal.
6. After completing the clearing, put the switch in the “OFF” position and disconnect the device from the
mains. Remember to thoroughly clean the device before winding the coil.
EN
12
Rev. 16.05.2022
13
Rev. 16.05.2022

Bekijk gratis de handleiding van MSW -POWER DRAIN CLEAN 2.3E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

MerkMSW
Model-POWER DRAIN CLEAN 2.3E
CategorieNiet gecategoriseerd
TaalNederlands
Grootte6598 MB