MSW -DRAIN CLEAN 2.3E handleiding
Handleiding
Je bekijkt pagina 8 van 33
Description of the device:
1. Handle
2. Motor switch
3. Lever
4. Enclosure
5. Coil
6. Protective gloves
7. Wrench
8. Tip set
9. Adjustable legs
10. Lubrication hole
1
2
3
4
5
6
7
8
9
10
MSW-POWER DRAIN CLEAN 2.3E
Description of the device:
1. Lever/handle
2. Locking lever/rear of the device
3. Coil
4. Protective gloves
5. Tip set
6. Legs
7. Wrenches
8. Tube
9. Container
10. Lubrication holes
10
1
2
3
4
5
6
7
8
9
MSW-POWER DRAIN CLEAN 4.6E
1
2
3
4
5
6
7
8
10
11
9
Description of the device:
1. Outlet nozzle
2. Lever
3. Protective pipe joint
4. Protective pipe
5. Coil
6. Protective gloves
7. Wrenches
8. Tip set
9. Motor
10. Wheels
11. Frame
DESCRIPTION OF THE DEVICE OPERATION – APPLICABLE TO MODELS MSW-DRAIN CLEAN 2.3E |
MSW-POWER DRAIN CLEAN 2.3E | MSW-POWER DRAIN CLEAN 4.6E
Operation:
1. Before commencing operation, ensure that neither the device nor the power cable are damaged. Next,
make sure that the switch at the motor is in the “OFF” position. If it is not, put it in the middle
position. And put the lever in the upper position.
2. Next:
• Adjust the legs and tighten the tting bolts (for models MSW-DRAIN CLEAN 2.3E | MSW-
POWER DRAIN CLEAN 2.3E)
• attach the protective pipe by inserting it into place (for model MSW-POWER DRAIN CLEAN
4.6E
and pull out an appropriate length of the selected coil. The method of connecting the coil can be found
below. When the coil is ready, attach an appropriate tip with the power supply turned off.
Or in the case of the model MSW-POWER DRAIN CLEAN 2.3E use the included tube instead of the
pipe.
3. Next, insert the coil prepared in advance into the opening of the device. Insert the coil in such a
way as to put the end of the coil without the tip into the opening located at the front of the device
– opposite the power cable (in the model MSW-POWER DRAIN CLEAN 4.6E, the coil should be
inside the protective pipe). Leave about 50cm of the coil in front of the device. When the device is
ready for clearing, connect it to the mains.
In the case of using the tube instead of the coil in the MSW-POWER DRAIN CLEAN 2.3E model,
insert the narrow end of the tube into the rear of the device (on the power cable side). In order to do
so, lift the locking pin located on the top of the enclosure, insert the tube and release the pin. Next,
check if the tube is sufciently stable and secured against falling out of the machine. Pull out enough
coil from the tube for the coil to protrude from the front of the device after attaching the pipe.
4. In order to start clearing, place the device about 50cm from the place of inserting the coil, insert the
coil into the opening in such a way as to prevent the coil from twisting and curling when the motor is
on and put the direction switch located at the engine in the “FOR” position – the engine of the device
is active, but the torque is not transmitted to the coil until the lever is put in the lower position. Next,
insert an appropriate length of the coil (pulling it out of the device) into the opening of the cleared
pipe. Use protective gloves! When the coil is in the right place, put the lever in the lower position start
clearing. In order to insert consecutive sections of the coil into the opening, put the lever in the upper
position, thus stopping the coil, then, wearing protective gloves, push another section in and put the
lever in the lower position again. Caution! When standing near the coil, remember about the existing
torsional torque. The coil can move independently at any time, even when the drive is off.
In the case of using a tube instead of a coil in the MSW-POWER DRAIN CLEAN 2.3E model, place
the device about 50cm from the place of inserting the coil and put the direction switch located at the
motor in the “FOR” position and put the lever in the lower position. Next, insert the coil into the
opening is such a way that prevents it from being twisted or curled when the device is on and start
clearing by putting the lever in the lower position.
The model MSW-POWER DRAIN CLEAN 2.3E is tted with a special lever lock. To engage
it, put the lever in the lower position and lock it with a handle (located next to the tube tting place)
by turning it clockwise. Thanks to this handle, the device can be conveniently carried using the lever. In
order to disengage the lock, press the lever down and turn the handle counter-clockwise.
You should always be prepared to stop the device in case of emergency
EN
14
Rev. 16.05.2022
15
Rev. 16.05.2022
Bekijk gratis de handleiding van MSW -DRAIN CLEAN 2.3E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | MSW |
| Model | -DRAIN CLEAN 2.3E |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6598 MB |
