MRCOOL MGM96SE090C4XA handleiding

Niet gecategoriseerd

MRCOOL

59 pagina's

PDF beschikbaar

Handleiding

507768C05

Page 15 of 57

mrcool.com

Capacity

Vent Pipe

Dia.

(in.)

Standard Concentric

Flush Mount Kit Wall Kit

Field

Fabricated

1-1/2 inch 2 inch 3 inch

51W11 (US)

51W12 (CA)

2 inch 3 inch

71M80 (US)

44W92

(CA)

69M29 (US)

44W92

(CA)

60L46 (US)

444W93

(CA)

22G44 (US)

30G28 (CA)

44J40 (US)

81J20 (CA)

045

1-1/2

YES YES

YES

N/A N/A

YES YES

YES

2-1/2

YES YES

YES

YES YES

YES

070

1-1/2 3YES YES

YES

2 3YES YES

YES

2-1/2

YES YES

YES

YES YES

YES

090

YES

N/A

YES

N/A

YES YES

2-1/2

YES YES

YES YES YES

YES YES

YES YES YES

110

2 YES YES

YES YES YES

2-1/2 YES YES

YES YES YES

3 YES YES

YES YES YES

135 3 YES YES

YES YES YES

NOTE - Standard Terminations do not include any vent pipe or elbows external to the structure. Any vent pipe or elbows external to the structure must be included in total

vent length calculations. See vent length tables.* Kits must be properly installed according to kit instructions.

1Requires eld-provided outdoor 1-1/2” exhaust accelerator.

2Concentric kits 71M80 and 44W92 include 1-1/2” outdoor accelerator, when used with 045 and 070 input models. When using 1-1/2 in. piping, the pipe must transition to

2in. pipe when used with the concentrci kit.

3 Flush mount kits 51W11 and 51W12 includes 1-1/2 in. outdoor exhaust accelerator, required when used with 045, 070 and 090 input models. When using 1-1/2 in. piping,

the pipe must transition to 2in. pipe when used with the ush mount kit.

4 Termination kits 30G28, 44W92, 44W93 and 81J20 are certied to ULC S636 for use in Canada only.

5 See table 10 for vent accelerator requirements

6 2inch to 1-1/2 inch reducer required. must be ed required.

Table 3. Outdoor Termination Kits Usage

Joint Cementing Procedure

All cementing of joints should be done according to the

specications outlined in ASTM D 2855.

NOTE: A sheet metal screw may be used to secure the

intake pipe to the connector, if desired. Use a drill or self

tapping screw to make a pilot hole.

DANGER OF EXPLOSION!

Fumes from PVC glue may ignite during system check.

Allow fumes to dissipate for at least 5 minutes before

placing unit into operation.

DANGER

1. Measure and cut vent pipe to desired length.

2. Debur and chamfer end of pipe, removing any ridges

or rough edges. If end is not chamfered, edge of pipe

may remove cement from tting socket and result in a

leaking joint.

3. Clean and dry surfaces to be joined.

4. Test t joint and mark depth of tting on outside of pipe.

5. Uniformly apply a liberal coat of PVC primer for PVC

or use a clean dry cloth for ABS to clean inside socket

surface of tting and male end of pipe to depth of tting

socket.

NOTE: Time is critical at this stage. Do not allow

primer to dry before applying cement.

Bekijk gratis de handleiding van MRCOOL MGM96SE090C4XA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.