Milwaukee M12 3450-20 handleiding
Handleiding
Je bekijkt pagina 5 van 16
5
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, use an OSHA
compliant dust extraction solution in accordance
with its operating instructions or wear appropri-
ate respiratory protection.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool on. The fuel gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1
light on the fuel gauge will ash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will ash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will ash and the tool will not run. Allow the battery
to cool down.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
For forward (clockwise) rotation, push in the control
switch from the right side of the tool. Check the
direction of rotation before use.
For reverse (counterclockwise) rotation, push in the
control switch from the left side of the tool. Check
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work while the
control switch is in the center locked position. Always
lock the trigger or remove the battery pack before
performing maintenance, changing accessories,
storing the tool and any time the tool is not in use.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handle(s) rmly and
pull the trigger.
NOTE: An LED is turned on when the trigger is
pulled and will go o shortly after the trigger is
released.
2. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed.
3. To stop the tool, release the trigger. Ensure the
tool has come to a complete stop before laying
the tool down.
Impacting Techniques
The longer a bolt, screw, or nut is impacted, the
tighter it will become. To help prevent damaging the
fasteners or workpieces, avoid excessive impact-
ing. Be particularly careful when impacting smaller
fasteners because they require less impacting to
reach optimum torque.
Practice with various fasteners, noting the length of
time required to reach the desired torque. Check the
tightness with a hand-torque wrench. If the fasteners
are too tight, reduce the impacting time. If they are
not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under
the head of the fastener aects the degree of tight-
ness.
SPECIFICATIONS
Cat. No. ..................................................... 3450-20
Volts .............................................................. 12 DC
Battery Type .................................................M12™
Charger Type ................................................M12™
RPM .......................................................... 0 - 3 000
IPM ........................................................... 0 - 4 100
Recommended Ambient
Operating Temperature .................... 0°F to 125°F
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with the charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always lock the trigger or remove
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Use only sockets and other accessories speci-
cally designed for use on impact wrenches and
drivers. Other sockets and accessories might
shatter or break causing injury.
Installing/Removing Hex Drive Chuck
This driver is intended for use with drill and driver
bits with a 1/4" hex shank and ball detent recess.
1. WARNING! Remove battery to avoid starting the tool.
2. To attach an accessory, pull out the ring (1) and
press the shank into the hex drive chuck (2).
3. To remove the accessory, pull out the ring (1)
and remove the accessory (2). Release the ring.
1
Attach Remove
1
2
2
Bekijk gratis de handleiding van Milwaukee M12 3450-20, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Milwaukee |
| Model | M12 3450-20 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2745 MB |
