Milwaukee M12 2525-20 handleiding
Handleiding
Je bekijkt pagina 5 van 24
5
Additional Safety Warnings
• The arbour size of wheels, sanding drum or any
other accessory must properly t the spindle or
collet of the power tool. Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may
cause loss of control.
• Mandrel mounted wheels, sanding drums, cutters
or other accessories must be fully inserted into
the collet or chuck. The "overhang" or the length
of the mandrel from the wheel to the collet must
be minimal. If the mandrel is insuciently held
and/or the overhang of the wheel is too long, the
mounted wheel may become loose and ejected at
high velocity.
• After changing the bits or making any adjust-
ments, make sure the collet nut, chuck or any
other adjustment devices are securely tightened.
Loose adjustment devices can unexpectedly shift,
causing loss of control, loose rotating components
will be violently thrown.
• Always feed the bit into the material in the same
direction as the cutting edge is exiting from the
material (which is the same direction as the chips
are thrown). Feeding the tool in the wrong direction
causes the cutting edge of the bit to climb out of the
work and pull the tool in the direction of this feed.
• When using steel saws, cut-o wheels, high speed
cutters or tungsten carbide cutters, always have
the work securely clamped. These wheels will
grab if they become slightly canted in the groove,
and can kickback. When a cut-o wheel grabs, the
wheel itself usually breaks. When the steel saw,
high-speed cutters or tungsten carbide cutter grab,
it may jump from the groove and you could lose
control of the tool.
• Do not position your hand in line with and behind
the rotating wheel. When the wheel, at the point
of operation, is moving away from your hand, the
possible kickback may propel the spinning wheel
and the power tool directly at you.
• Allow brushes to run at operating speed for at
least one minute before using them. During this
time no one is to stand in front or in line with the
brush. Loose bristles or wires will be discharged
during the run-in time.
•Direct the discharge of the spinning wire brush
away from you. Small particles and tiny wire frag-
ments may be discharged at high velocity during the
use of these brushes and may become imbedded
in your skin.
•
WARNING
To reduce the risk of injury, when
working in dusty situations, wear
appropriate respiratory protection or use an
OSHA compliant dust extraction solution.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
UL Listing for Canada and U.S.
SPECIFICATIONS
Cat. No. ..................................................... 2525-20
Volts.............................................................. 12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
No Load RPM ................................... 5000 - 27,500
Collet ...............................................................1/8"*
Max Accessory Diameter ....................... 2" / 55 mm
Recommended Ambient
Operating Temperature ......................0°F to 125°F
* Also accepts standard collet sizes 1/32", 1/16", 3/32" (sold
separately)
FUNCTIONAL DESCRIPTION
4
1
5
7 8
6
2
3
1. Collet nut
2. Nose collar
3. LED
4. Spindle lock
5. ON/OFF switch
6. Handle
7. Fuel gauge
8. Speed selector
Collet nut
Collet
Nose collar
Spindle
Bekijk gratis de handleiding van Milwaukee M12 2525-20, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Milwaukee |
| Model | M12 2525-20 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4529 MB |
