Milwaukee 6033-21 handleiding
Handleiding
Je bekijkt pagina 4 van 20
4
ASSEMBLY
WARNING
To reduce the risk of injury, always
unplug tool before changing or
removing accessories. Only use accessories
specically recommended for this tool. Others
may be hazardous.
Selecting Sandpaper and Grits
Sandpaper can be made from various grit materials
and these should be selected according the material
to be sanded. The guidelines below list materials and
grit materials that should be used with them.
•Fine woodwork – garnet or aluminum oxide
•Rough woodwork – aluminum zirconia or ceramic
aluminum oxide
•Manufactured wood products (particleboard,
medium density ber board etc.) – silicon carbide
or aluminum oxide
•Solid surfacing materials (Corian, etc.) – silicon
carbide or aluminum oxide
•Metals – emery or aluminum oxide
Sandpaper is also graded by coarseness. Start
your work with an abrasive grit just coarse enough
to remove high spots and excessive roughness.
Follow with a second sanding using a grit one or
two grades ner. Continue with successively ner
grits until you obtain the desired nish.
Grit Type Typical Application
60
80
Coarse
Ideal for initial sanding on rougher
surfaces. For fast stock removal.
Rough sanding and stripping of
painted and rusted surfaces.
100
120
Medium
For intermediate sanding
and removal of minor surface
imperfections.
150
180
220
Fine
Ideal for ne sanding prior to strain-
ing, priming, or sealing.
Do not switch from a coarse grit to a very ne grit in
one step because it may be dicult to remove the
marks made by the coarse grit abrasive. Use the
nest grits practical for the roughing operation, and
nish by using successively ner grits.
Installing Sandpaper
Inspect sandpaper before installing. DO NOT use if
broken, ripped or defective.
1. Unplug the sander.
2. Push in the front clamp (1) and insert the end
of new 1/4 sheet sandpaper approximately 1/4"
between the clamp and the sanding pad. Release
the front clamp.
3. Open the rear clamp (2) by pushing the lever up
and out of the catch. Open the clamp fully.
4. Wrap the sandpaper around the sanding pad,
moulding the sandpaper to the base.
5. Smooth the paper against the sanding pad and
close the rear clamp (3). Ensure the paper is pulled
tight under the rear clamp. Secure the lever in the
clamp catch.
6. Multiple sheets of sandpaper can be installed at
one time for convenience.
SYMBOLOGY
Double Insulated
Volts
Alternating Current
Alternating Current/Direct Current
Amps
OPM
Orbits Per Minute (OPM)
C
US
UL Listing for Canada and U.S.
SPECIFICATIONS
Cat. No. ..................................................... 6033-21
Volts .............................................................120 AC
Amps .....................................................................3
OPM .............................................................14,000
Paper Size ................................................1/4 sheet
FUNCTIONAL DESCRIPTION
1. Gripping surface
2. On/O switch
3. Front clamp
4. Sanding pad
5. Dust box with lter
6. Universal hose
adapter
7. Rear clamp lever
8. Clamp catch
9. Paper punch
(not shown)
3
5
2
7
8
1
4
6
Bekijk gratis de handleiding van Milwaukee 6033-21, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Milwaukee |
| Model | 6033-21 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3668 MB |
