Metro C533-CLFC-L handleiding
Handleiding
Je bekijkt pagina 12 van 32
C5 1-3 SERIES HOLDING & PROOFING CABINETS — INSTRUCTIONS FOR USE
12
www.metro.com
L01-430
REV W 01/22
CARE & MAINTENANCE
Cleaning The Cabinet
Warning: Unplug the cabinet before cleaning or servicing. Do not wash the cabinet with a water jet or high-pressure
water.
Warning: Allow the unit to cool before cleaning, as the interior of the cabinet may be hot enough to burn. Also, allow
the water in the pan to cool before removal.
Caution: Do not spray or pour water into the control module. To clean the cabinet and module, wipe with a damp cloth
and dry with a towel. Use only cleaning agents approved for aluminum.
Caution: Do not use strong alkalis as it may discolor aluminum.
• Use cleaners in the proper concentrations. Follow the manufacturer’s directions for the cleaning product used. After
using any cleaning products, thoroughly rinse all surfaces to remove all residue.
• Use a damp cloth or sponge. Mild soap suitable for aluminum is acceptable. Dry with a clean towel. Wipe up spills as
soon as possible and regularly clean the cabinet to avoid staining and difficult to clean conditions.
• If a control knob needs to be removed for cleaning, remove the knob, clean the knob recess and knob, and replace the
knob.
1. When removing the module, make sure the power cord is NOT plugged into the wall receptacle or hooked onto the
cord keeper. Open the door(s). If there is water in the stainless steel pan, remove and empty. Remove the module
from the cabinet by lifting up the front enough to clear its detent, and then pull the module away from the cabinet. The
power cord slips through the clearance hole at the rear of the cabinet.
2. Remove the slide racks.
3. After cleaning, replace all components. Make sure the slide racks are seated in the hangers correctly.
4. Push the power cord through the plastic snap bushing in the rear of the cabinet and install the module.
Cleaning Instructions for Clear, Polycarbonate Doors (if applicable):
The protective masking on the polycarbonate door may be removed by simply peeling it from the door, starting at a
top corner and working downward. For regular cleaning, a soft cotton flannel cloth and a cleaner recommended by its
manufacturer for use on polycarbonate plastics is suggested. Do not use synthetic cloths or cleaners not intended for
polycarbonate plastics as these will scratch and dull the polycarbonate door panel. Additional hints for keeping the door
panel clean and clear:
1. Isopropyl (rubbing) alcohol, used as a cleaner, will aid in removing grease smudges and fingerprints.
2. A small amount of liquid dish detergent in a bucket of water will help remove heavier dirt and will help make the clear
panel antistatic and therefore less likely to attract dust.
3. A paste-wax recommended for polycarbonate plastics and approved for food service equipment will hide small
scratches and return the luster and clarity to the clear door panel as well as reduce the electrostatic attraction
of dust.
Cleaning Instructions for 3 Series Insulation Armour Panels on Sides, Top and Back:
Use soft cloth, mild soap water solution to clean lightly-soiled surfaces. Then wipe dry with a clean, soft cloth. For heavily-
soiled areas, use a soft brush and solvent or emulsion-based cleaner. Always insure the cleaner is recommended for use
on plastics and follow any special instructions from the manufacturer.
Cabinet Maintenance:
Regularly inspect this product. Tighten loose fasteners and replace worn or damaged parts with new InterMetro approved
parts. For mobile units, replace worn or damaged casters immediately; if equipped with grease fittings, lubricate casters
regularly.
Bekijk gratis de handleiding van Metro C533-CLFC-L, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Metro |
| Model | C533-CLFC-L |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5137 MB |
