Metra 99-3028S handleiding
Handleiding
Je bekijkt pagina 16 van 20
386.257.1187
|
MetraOnline.com
16
STEERING WHEEL CONTROL SETTINGS
LED Feedback
The (24) Red LED flashes represent what brand radio the Axxess interface believes it is
connected to. Each flash represents a different radio Manufacturer. For example, if you are
installing a JVC radio, the Axxess interface will flash Red (5) times, and then stop. Following is a
legend that dictates which radio Manufacturer corresponds to which flash.
LED feedback legend
* Note:
If the Axxess interface flashes Red (7) times, and you do not have an Alpine radio
connected to it, that means the Axxess interface does not detect a radio connected to it.
Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.
** Note:
The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must have
rev. 2.1.4 or higher software.
† Note:
If you have a Clarion radio and the steering wheel controls do not work, change the radio
type to the other Clarion radio type; same for Eclipse. The following section explains how to do this
.
‡ Note:
If you have a Kenwood radio and the LED feedback comes back showing as a JVC radio,
change the radio type to Kenwood. The following section explains how to do this.
Changing Radio Type
If the LED flashes do not match the radio you have connected, you must manually program the
Axxess interface to tell it what radio it is connected to.
1. After (3) seconds of turning the key on, press and hold the Volume Down button on the
steering wheel until the LED in the Axxess interface goes solid.
2. Release the Volume Down button; the LED will go out indicating the Axxess interface is in
Changing Radio Type mode.
3. Refer to the Radio Legend on the next page to know which radio number you would like to
have programmed.
4. Press and hold the Volume Up button until the LED goes solid, and then release. Repeat this
step for the desired radio number you have selected.
5. Once the desired radio number has been selected, press and hold the Volume Down button
on the steering wheel until the LED goes solid. The LED will remain on for about (3) seconds
while it stores the new radio information.
6. Once the LED goes out, the Changing Radio Type mode will then end. You can now test the
steering control wheel controls.
Note: If at any time the user fails to press any button for a period longer than (10) seconds,
this process will abort.
Continued on the next page
Attention: The Axxess Updater App can also be used to program the following (3) sub-sections as
well, pending that the Axxess interface has been programmed.
1 Flash - Eclipse (Type 1) †
2 Flashes - Kenwood ‡
3 Flashes - Clarion (Type 1) †
4 Flashes - Dual / Sony
5 Flashes - JVC
6 Flashes - Boss (Type 1)/Jensen/Pioneer
7 Flashes - Alpine *
8 Flashes - Visteon
9 Flashes - Valor
10 Flashes - Clarion (Type 2) †
11 Flashes - Boss (Type 2)
12 Flashes - Eclipse (Type 2)
13 Flashes - LG
14 Flashes - Parrot
15 Flashes - XITE
16 Flashes - Philips
17 Flashes - Kicker
18 Flashes - JBL
19. Flashes - Insane Audio
20 Flashes - Axxera/Magnadyne
21 Flashes - Boss (Type 3)
22 Flashes - Axxera
23 Flashes - Axxerra (Type 2)
24 Flashes - Alpine (Type 2)
Bekijk gratis de handleiding van Metra 99-3028S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Metra |
| Model | 99-3028S |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2218 MB |
