Handleiding
Je bekijkt pagina 11 van 76
en
it
de
es
fr
nl
pt
da
no
sv
pl
ru
cs
hu
sl
tr
hr
lt
lv
et
ro
sk
bg
uk
bs
el
zh
►►►6. SWITCHING ON AND OFF
WARNING: You are required to read, understand and follow the
''INFORMATION ON SAFETY'' before starting the heater in order to
use it correctly and avoid risks.
IMPORTANT: In order to use the heater, the battery-operated wire-
less remote control (ACCESSORY) must be purchased.
►►6.1. SWITCH-ON
►6.1.1. Supply power and set the main power switch to the 'I/ON' position.
►6.1.2. To operate the heater, the turn-on procedure must be set on the
battery-operated wireless remote control (ACCESSORY).
A series of sensors check that the heater is operating correctly and stops the
appliance in the event of a serious fault.
A lack of ventilation activates the safety device which stops all heater func-
tions when the internal temperature of the device exceeds 90°C. The heater
will not resume operation automatically, this must be performed manually.
PROCEED AS FOLLOWS:
→1. Wait for the heater to cool down completely.
→2. Set the main power switch to the ”0/OFF” position.
→3. Disconnect the heater from the electrical power supply.
→4. Eliminate the possible cause of the heater block (e.g. obstructed air
vent, impaired air supply, etc.).
→5. Firmly press the “RESET” button located on the top of the heater.
→6. Reconnect the heater to the power supply.
→7. Set the main power switch to the “I/ON” position.
→8. Switch the heater from the battery-operated wireless remote control
(ACCESSORY) back on to full power and check for about an hour that
the device does not lock up again.
→9. If, after a few attempts to resume operation, the heater does not work,
contact the support centre.
►►6.2. SHUTDOWN (FOR A SHORT PERIOD)
►6.2.1. To shut down the heater, the shutdown procedure must be set on
the battery-operated wireless remote control (ACCESSORY).
►►6.3. DECOMMISSIONING (LONG-TERM)
►6.3.1. To shut down the heater, the shutdown procedure must be set on
the battery-operated wireless remote control (ACCESSORY).
►6.3.2. Set the main power switch to the “0/OFF” position.
►6.3.3. Disconnect the heater from the electrical power supply.
NOTE: AVOID DISCONNECTING THE HEATER FROM THE ELECTRICAL
POWER SUPPLY BEFORE THE FAN HAS COMPLETELY STOPPED, IN
ORDER TO AVOID SERIOUS DAMAGE.
►►►7. MAINTENANCE AND STORAGE
Any maintenance or cleaning work should only be carried out after the
heater has been switched o, is cold and disconnected from the power sup-
ply. Dust that may accumulate in the heater can restrict heat exchange and
thus pose a risk of re and overheating. It is essential to keep the heater in
good working order by cleaning it regularly with compressed air and a soft,
solvent-free cloth.
Always disconnect the heater from the mains when not in use for a long
period.
When the heater is used again, check the condition of the power supply
cable; if in doubt regarding its state, contact the support centre.
In any case, have the service centre check the correct functioning of the
heater at least once a year and/or as needed.
►►►8. TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
The heater doesn't
work
1. Main power supply switch in position “0/
OFF”
2. Incorrect setting of battery-operated
wireless remote control
3. No power supply
4. Blocked heater
1. Set the main power switch to the “I/ON” position
2a. Switch on the battery-operated wireless remote control with the “ON/OFF”
button and select the desired mode
2b. Check that the temperature set on the battery-operated wireless remote
control is higher than the outside temperature
3a. Insert the power supply cable correctly
3b. Make sure your mains power supply is working correctly
3c. Contact the support centre
4a. Reset the heater by pressing the “RESET” button
4b. Contact the support centre
The motor doesn't
work
1. Faulty motor
2. Blocked fan
1. Contact the support centre
2a. Remove any obstructions
2b. Contact the support centre
The heater doesn't
heat
1. Battery-operated wireless remote control set
to “FAN”
2. Faulty internal appliance
1. Change the setting on battery-operated wireless remote control
2. Contact the support centre
Reduced airow 1. Obstructed air vent
2. Faulty motor
1a. Remove any obstructions
1b. Contact the support centre
2. Contact the support centre
Bekijk gratis de handleiding van Master TR 3D, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Master |
| Model | TR 3D |
| Categorie | Heater |
| Taal | Nederlands |
| Grootte | 14709 MB |
