Makita VR1000 handleiding
Handleiding
Je bekijkt pagina 6 van 44
6 ENGLISH
WARNING: The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING: Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, re and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Concrete vibrator safety warnings
1. Always keep your hands and face away from
vibrating head when operating.
2. Switch off the tool immediately if you notice
abnormal noise or something faulty during
operation.
3. Inspect the tool carefully for breakage, cracks
or deformation if you accidentally drop it or
strike it against something.
4. Do not carry the tool with nger on switch.
5. Do not set the tool down and switch it on. The
vibrating head may whip around out of control
and cause an accident.
6. Be careful not to allow water, wet concrete or
the like to get into the tool. Do not let the tool
fall into wet concrete.
7. Insert the vibrating head carefully between
iron/steel frames or reinforcing rods not to
come in contact with them.
8. Do not crush or twist the exible hose.
9. Do not overly bend the exible hose.
10. Use a wet cloth or the like to carefully wipe
off any wet concrete left on the tool after use.
Extra care should be given to thorough clean-
ing of the vents, switch area, cover openings,
etc.
11. Do not use the tool in the rain. Do not clean the
tool in water.
12. After operating the tool, switch off the tool
and wait until the vibration of the exible shaft
stops completely before putting down the tool.
13. After operating the tool, do not touch the
vibrating part as it may be extremely hot and
could burn your skin.
14. Do not operate the tool outside of concrete.
The vibrating part is cooled down by inserting the
vibrating part into concrete.
15. If the power is cut off due to power failure
or the disconnection of power plug, set the
switch to the off position.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched off and unplugged before adjusting or
checking function on the tool.
Residual current device
WARNING: Do not use the tool if the pilot
lamp does not go out when the TEST button is
pushed.
The tool is equipped with either of Residual Current
Device (RCD) shown in the gure.
► Fig.1: 1. Pilot lamp 2. RESET button 3. TEST
button
► Fig.2: 1. RESET button 2. Pilot lamp 3. TEST
button
Connect the tool to a power supply and test the
Residual Current Device (RCD) before using the tool.
Push the RESET button and conrm that the pilot lamp
lights. Push the TEST button and conrm that the pilot
lamp goes out. Push the RESET button again to use
the tool.
Switch action
CAUTION: Before plugging in the tool, always be
sure that the tool is switched off.
► Fig.3: 1. Switch
To start the tool, press the position marked (I) on the
switch. To turn off the tool, press the position marked (0)
on the switch.
Bekijk gratis de handleiding van Makita VR1000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | VR1000 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6282 MB |
