Makita UT1305 handleiding
Handleiding
Je bekijkt pagina 6 van 40
6 ENGLISH
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o and unplugged before carrying out
any work on the tool.
Installing the shaft
1. Tighten the shaft into the shaft holder till the hex
nut contacts with the shaft holder.
►Fig.4: 1. Hex nut 2. Shaft 3. Shaft holder
2. Hold the notch in the shaft holder with wrench 19
so that it cannot revolve. With the notch held so, tighten
the hex nut with another wrench 19 in the direction of
arrow.
►Fig.5: 1. Wrench 19 2. Notch 3. Wrench 19
Installing the mixing blade
►Fig.6
To mount the mixing blade, install it with the " UP " mark
onitfacingthetool(directinginside).
Install the mixing blade on the top of shaft and secure it
with hex bolt.
►Fig.7: 1. Mixing blade 2. Shaft 3. Hex bolt
Incaseofmixingblade150(accessory),screwit
directly on the top of shaft as it is threaded.
OPERATION
CAUTION: Do not mix ammable materials or
operate the tool around ammable materials such
as paint with thinner used as solvent. Failure to do
somaycauseaninjury.
CAUTION: When you mix the material while
the mixing blade oating out of the material, be
careful not to splash the material.
1. Hold the rear handle of the tool with one hand
andthegripwiththeotherhandrmly,placethemixing
blade under material fully and turn on the tool after
making sure work site safety.
2. Move the mixing blade up and down during the
mixing operation so that whole part of material can be
mixed.
3. Whennishingmixing,turnothetool,makesure
that the mixing blade has come to a complete stop, and
then pull it out of the mixing container.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched o and unplugged before attempting to
perform inspection or maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Replacing lter
►Fig.8: 1. Filter 2. Cover 3. Screwdriver
Replacethelterregularlyasthecoolingeciencyof
the tool is reduced due to built-up dust or particles in
thelter.
Insert the slotted bit screwdriver and the like between
thetoolandthecoverasshowninthegure.Liftitup
justlikeusingashovelandremovethecover.
Replacethelterinthecoverwithanewone.
Reinstall the cover on the tool.
Replacing carbon brushes
►Fig.9: 1. Limit mark
Check the carbon brushes regularly.
Replace them when they wear down to the limit mark.
Keep the carbon brushes clean and free to slip in the
holders.Bothcarbonbrushesshouldbereplacedatthe
same time. Use only identical carbon brushes.
1. Use a screwdriver to remove the brush holder
caps.
2. Take out the worn carbon brushes, insert the new
ones and secure the brush holder caps.
►Fig.10: 1.Brushholdercap
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual. The use of any other
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Mixing blade
Type Maximum diameter Twin blade
possible
Mixing blade 130 130 mm -
Mixing blade 150 150 mm -
Mixing blade 165 165 mm -
• Shaft
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
dierfromcountrytocountry.
Bekijk gratis de handleiding van Makita UT1305, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | UT1305 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5485 MB |
Caratteristiche Prodotto
| Kleur van het product | Black, Blue, Stainless steel |
| Gewicht | 3200 g |
| Breedte | 942 mm |
| Diepte | 87 mm |
| Hoogte | 152 mm |
