Makita UT002G handleiding
Handleiding
Je bekijkt pagina 11 van 84
11 ENGLISH
Operation of speed change knob
NOTICE: Use the speed change knob only after
the tool comes to a complete stop. Changing the
tool speed mode before the tool stops may damage
the tool.
NOTICE: Always set the speed change knob
carefully into the correct position. If you operate
the tool with the speed change knob positioned half-
way between the position 1 and the position 2, the
tool may be damaged.
NOTICE: If the rotation speed signicantly
decreases during operation in the high speed
mode, stop the tool and change the mode to the
low speed mode. Otherwise, the motor may get
overloadedandcauseamalfunctionorre.
Two speed ranges can be preselected with the speed
change knob.
Select the proper speed mode for the material to be
mixed.
To change the speed mode, turn the speed change
knob so that the pointer points to the dot at position
1 for low speed mode or the dot at position 2 for high
speed mode.
►Fig.16: 1. Pointer 2. Speed change knob 3. Dot
Operation of speed adjusting dial
Thetoolspeedcanbeadjustedsteplesslybyturning
thespeedadjustingdial.Thenoloadspeedwhenthe
switchtriggerisfullypulledcanbeadjusted270min
-1
to 500 min
-1
at low speed mode, 500 min
-1
to 920 min
-1
at high speed mode. Higher speed is obtained when
the dial is turned in the direction of number 5; lower
speed is obtained when it is turned in the direction of
number 1.
Select the proper speed for the material to be mixed.
►Fig.17: 1.Speedadjustingdial
NOTICE: The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1.
Accidental restart preventive
function
If you install the battery cartridge while pulling the
switch trigger or locking the switch trigger, the tool does
not start. To start the tool, release the switch trigger, and
then pull the switch trigger.
Electronic function
The tool is equipped with the following electronic func-
tion for easy operation.
Soft start
The soft-start function minimizes start-up shock, and
makes the tool start smoothly.
Basic operations
CAUTION: Do not mix ammable materials or
operate the tool around ammable materials such
as paint with thinner used as solvent. Failure to do
somaycauseaninjury.
CAUTION: Do not mix high viscosity material
in the high speed mode. You may lose the control of
thetoolandcauseaninjury.
CAUTION: Do not rotate the mixing blade
outside the stirring vessel.
CAUTION: If you hear an abnormal noise
during use, turn o the switch and stop using the
tool.
NOTICE: When you mix the material while the
mixing blade oating out of the material, be care-
ful not to splash the material.
NOTICE: Do not use the tool for any purpose
other than stirring mortar, concrete, etc.
1. Select high speed mode or low speed mode
according to the material to be mixed.
2.
Holdthetoolrmlywithbothhands.Placethemixing
blade under material fully. Check that the material is not
solidiedandthesafetyoftheworksite,thenturnonthetool.
3. Move the mixing blade up and down during the
mixing operation so that whole part of material can be
mixed.
4. Whennishingmixing,turnothetool.Makesure
that the mixing blade has come to a complete stop, and
then pull it out of the mixing container.
Applied operations
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before adjusting or checking function on the tool.
Replacing battery cover
Optional accessory
Installoneofthebatterycoverstotthesizeofyour
battery cartridge.
►Fig.18:
1. Battery cover S 2. Battery cover L 3. Button
1. Open the standard equipped battery cover while
pressing the button on the battery cover.
2. Loosen the screw securing the standard equipped
battery cover. Then remove the screw, sleeve and the
battery cover.
►Fig.19: 1. Screw 2. Sleeve 3. Battery cover (stan-
dard equipped)
NOTE: The sleeve may remain in the mounting holes.
In that case, pull it out using a screw or the like.
3. Align the mounting hole on the optional battery
cover with the mounting holes on the housing. Insert the
sleeve. Then tighten the screws to secure it in place.
►Fig.20:
1. Screw 2. Sleeve 3. Battery cover (optional)
4. Close the battery cover securely.
Bekijk gratis de handleiding van Makita UT002G, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | UT002G |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 12657 MB |
