Makita TW010G handleiding
Handleiding
Je bekijkt pagina 9 van 92
9 ENGLISH
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
When the reversing switch lever is on the side A or side
B and the switch trigger is pulled, the front lamp turns
on.Toturno,releasetheswitchtrigger.Thefrontlamp
goesoutapproximately10secondsafterreleasingthe
switch trigger.
►Fig.5: 1. Front lamp
Changing brightness
To change the brightness, press the button . The
brightnesshasthreelevels.Everytimeyoupressthe
button ,thebrightnessdecreasesandnallygoes
out.Whenthelampstatusiso,thefrontlampwillnot
turn on even if the switch trigger is pulled. To turn on the
lamp status again, press the button . The brightness
will return to the highest.
►Fig.6: 1. Switch panel 2. Button
NOTE:Toconrmthelampstatus,pulltheswitch
trigger.Whenthefrontlamplightsupbypullingthe
switch trigger, the lamp status is ON. When the front
lamp does not light up, the lamp status is OFF.
NOTE: When the tool is overheated, the front lamp
ashesforoneminute,andthenthelampsonthe
switchpanelgoo.Inthiscase,cooldownthetool
before operating again.
NOTE:Useadryclothtowipethedirtothelensof
the front lamp. Be careful not to scratch the lens of
thefrontlamp,oritmaylowertheillumination.
NOTE: While pulling the switch trigger, the lamp
status cannot be changed.
NOTE:Forapproximately10secondsafterreleasing
the switch trigger, the lamp status can be changed.
Light mode
You can use the tool as a light.
To turn on the light, set the reversing switch lever in the
neutral position and pull the switch trigger.
Thefrontlampkeepslightingupforapproximatelyone
hour.
Toturnothelight,pulltheswitchtriggeragain.
Changing brightness
To change the brightness, press the button . The
brightnesshasthreelevels.Everytimeyoupressthe
button , the brightness decreases. The brightness
will return to the highest when operating in the lowest
brightness.
NOTE: You cannot change the application mode
while the light mode is on. The lamps on the switch
panel do not light up when the light mode is on.
NOTE:Youcannotturnon/othelampstatuswhen
the light mode is on.
NOTE: The light mode does not work when the tool/
batteryprotectionsystemactivatesorthebattery
capacityisnotenough.
Changing the application mode
Changing the impact force
You can change the impact force in four steps: 4 (max), 3 (hard), 2 (medium), and 1 (soft).
This allows a tightening suitable to the work.
Theleveloftheimpactforcechangeseverytimeyoupressthebutton .
Youcanchangetheimpactforcewithinapproximatelyoneminuteafterreleasingtheswitchtrigger.
NOTE:Youcanextendthetimetochangetheimpactforceapproximatelyoneminuteifyoupressthebut-
ton
or .
►Fig.7: 1. Button
Application mode
(Impact force grade
displayed on panel)
Maximum blows Purpose
TW009G TW010G
4 (Max)
1,750 min
-1
(/min) Tightening with the maximum force and speed.
Tightening when the force and the speed are desired.
Bekijk gratis de handleiding van Makita TW010G, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | TW010G |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13353 MB |
