Makita HS013G handleiding

Handleiding

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132/ 132

Afdrukken

Je bekijkt pagina 13 van 132

13 ENGLISH

Indicator lamps Remaining

capacity

Lighted O󰀨 Blinking

Thebattery

mayhave

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydi󰀨erslightly

fromtheactualcapacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

thebatteryprotectionsystemworks.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutso󰀨powertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placed under one of the following conditions.

Overload protection

Whenthetool/batteryisoperatedinamannerthat

causesittodrawanabnormallyhighcurrent,thetool

automaticallystops.Inthissituation,turnthetoolo󰀨

and stop the application that caused the tool to become

overloaded. Then turn the tool on to restart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically.Inthissituation,letthetoolcooldown

before turning the tool on again.

Overdischarge protection

Whenthebatterycapacitybecomeslow,thetoolstops

automatically.Iftheproductdoesnotoperateeven

when the switches are operated, remove the bat-

tery(ies)fromthetoolandchargethebattery(ies).

Protections against other causes

Protectionsystemisalsodesignedforothercauses

that could damage the tool and allows the tool to stop

automatically.Takeallthefollowingstepstoclearthe

causes,whenthetoolhasbeenbroughttoatemporary

halt or stop in operation.

1. Makesurethatallswitch(es)is/areintheo󰀨posi-

tion, and then turn the tool on again to restart.

2. Chargethebattery(ies)orreplaceit/themwith

rechargedbattery(ies).

3. Letthetoolandbattery(ies)cooldown.

Ifnoimprovementcanbefoundbyrestoringprotection

system,thencontactyourlocalMakitaServiceCenter.

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

WARNING: NEVER defeat the lock-o󰀨 button

by taping down or some other means. A switch with

anegatedlock-o󰀨buttonmayresultinunintentional

operationandseriouspersonalinjury.

WARNING: NEVER use the tool if it runs when

you simply pull the switch trigger without press-

ing the lock-o󰀨 button. A switch in need of repair

mayresultinunintentionaloperationandserious

personalinjury.ReturntooltoaMakitaservicecenter

for proper repairs BEFORE further usage.

Topreventtheswitchtriggerfrombeingaccidentally

pulled,alock-o󰀨buttonisprovided.Tostartthetool,

depressthelock-o󰀨buttonandpulltheswitchtrigger.

Release the switch trigger to stop.

►Fig.9: 1. Switch trigger 2.Lock-o󰀨button

NOTICE: Do not pull the switch trigger hard

without pressing in the lock-o󰀨 button. This can

cause switch breakage.

CAUTION: The tool starts to brake the cir-

cular saw blade rotation immediately after you

release the switch trigger. Hold the tool rmly to

respond the reaction of the brake when releasing

the switch trigger. Sudden reaction can drop the tool

o󰀨yourhandandcancauseapersonalinjury.

Adjusting depth of cut

CAUTION: After adjusting the depth of cut,

always lock the base.

1. Unlockthebasebylooseningthelever.

2. Setthecircularsawbladetoyourdesiredcutting

depth.

3. Lockthebasebytighteningthelever.

►Fig.10: 1. Base 2. Cutting depth 3. Lever

CAUTION: For cleaner, safer cuts, set cut

depth so that no more than one blade tooth

projects below workpiece. Using proper cut

depth helps to reduce potential for dangerous

KICKBACKS which can cause personal injury.

Bevel cutting

CAUTION: After adjusting the bevel angle,

always lock the base.

1. Loosen the lever and clamping screw.

2. Alignthepointerwithyourdesiredcuttingangleby

tilting the base.

3. Tightentheleverandclampingscrewsecurely.

►Fig.11: 1. Lever 2. Clamping screw 3. Pointer

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132/ 132

Bekijk gratis de handleiding van Makita HS013G, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Makita (Niet gecategoriseerd)

Handleiding bekijken

Makita 197235-3

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita CA5000

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita BL3622A

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DBN601

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DBN610

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DHP490

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DDF490

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DFJ214

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd