Makita DDF490 handleiding
Handleiding
Je bekijkt pagina 8 van 68
8 ENGLISH
Speed change
CAUTION: Always set the speed change lever
fully to the correct position.Ifyouoperatethe
toolwiththespeedchangeleverpositionedhalfway
betweenthe"1"sideand"2"side,thetoolmaybe
damaged.
CAUTION: Do not use the speed change lever
while the tool is running.Thetoolmaybedamaged.
Displayed
Number
Speed Torque Applicable
operation
1 Low High Heavyload-
ing operation
2 High Low Light loading
operation
Tochangethespeed,switchothetoolrst.Pushthe
speedchangelevertodisplay"2"forhighspeedor"1"for
lowspeedbuthightorque.Besurethatthespeedchange
leverissettothecorrectpositionbeforeoperation.
Ifthetoolspeediscomingdownextremelyduringthe
operationwithdisplay"2",pushthelevertodisplay"1"
and restart the operation.
►Fig.6: 1. Speed change lever
Selecting the action mode
This tool has two action modes.
Drillingmode(rotationonly)
1 - 20 Screwdriving mode (rotation
with clutch)
Selectthemodesuitableforyourwork.Turntheadjust-
ingringandalignthemarkthatyouselectwiththe
arrowonthetoolbody.
►Fig.7: 1.Adjustingring2. Mark 3.Arrow
NOTICE:Alwayssettheringcorrectlytoyour
desiredmodemark.Ifyouoperatethetoolwiththe
ringpositionedhalfwaybetweenthemodemarks,the
toolmaybedamaged.
NOTICE: Do not change the action mode while tool
is rotating.
NOTICE:Ifitisdiculttoslidetheadjustingring,
switch on and run the tool for a second, then stop
thetoolandslidetheadjustingringtoyourdesired
position again.
Adjusting the fastening torque
Thefasteningtorquecanbeadjustedin21levelsbyturningtheadjustingring.Alignthegraduationswiththearrow
onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat marking.
Theclutchwillslipatvarioustorquelevelswhensetatthenumber1to20.Theclutchdoesnotworkat
the marking.
►Fig.8: 1.Adjustingring2. Graduation 3.Arrow
Beforeactualoperation,driveatrialscrewintoyourmaterialorapieceofduplicatematerialtodeterminewhich
torque level is required for a particular application.
Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.
Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Machine screw M4 M5 M6
Wood
screw
Soft wood
(e.g. pine)
– ø3.5 x 22 ø4.1x 38 –
Hard wood
(e.g. lauan)
– ø3.5 x 22 ø4.1x 38 –
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
drill bit
Optional accessory
Turn the sleeve counterclockwise to open the chuck
jaws.Placethedriverbit/drillbitinthechuckasfar
as it will go. Turn the sleeve clockwise to tighten the
chuck.Toremovethedriverbit/drillbit,turnthesleeve
counterclockwise.
►Fig.9: 1. Sleeve 2. Close 3. Open
Installing hook
Optional accessory
WARNING: Use the hanging/mounting parts
for their intended purposes only, e.g., hanging the
tool on a tool belt between jobs or work intervals.
WARNING: Be careful not to overload the
hook as too much force or irregular overburden
may cause damages to the tool resulting in per-
sonal injury.
Bekijk gratis de handleiding van Makita DDF490, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | DDF490 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10239 MB |
