Makita CA5000 handleiding
Handleiding
Je bekijkt pagina 9 van 64
9 ENGLISH
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched o and unplugged before adjusting or
checking function on the tool.
Quick stop for 3, 4, or 6 mm board
thickness groove cutting
By turning the quick stop, you can choose the appro-
priate depth of groove cutting for 3, 4, or 6 mm board
thickness swiftly.
The number, seen from the handle side, indicates the
workpiece board thickness.
Forneadjustmentofdepthofgroove,usethedepth
adjustingknob.
►Fig.7: 1. Quick stop 2.Depthadjustingknob
0 mm depth is set properly when the tool is shipped
from the factory, but if you changed the depth of groove
bytheadjustingknob,renethe0mmdepthasfollows:
1. Turn the quick stop to 0 mm.
2. Turnthedepthadjustingknobtoadjustthedepth.
3. Make sure that the blade does not make any
contact with work piece.
4. Holdthetoolrmlywithonehandonthefrontgrip
andtheotheronthetoolhandle.Pushinthelock-o
button, and turn the tool on.
5. Slowly press down the saw head fully, and check
whether the groove cutter blade does not contacts but
almost touches the workpiece. If not, stop the tool and
wait until the groove cutter blade stops completely, and
adjustthedepthbyturningthedepthadjustingknob
again.
Adjusting depth of cut
Toadjustdepthofcut,turnthedepthadjustingknob.
For deeper cut, turn it clockwise. For shallower cut, turn
it counterclockwise.
►Fig.8: 1.Depthadjustingknob
Sighting
Triangular mark on the base indicates the center of the
groove cutter blade.
When using with groove cutter blade, align the outside
triangular mark with the cutting line.
When using with circular saw blade (optional acces-
sory), align the inside triangular mark with the cutting
line.
►Fig.9: 1. Base 2. Outside triangular mark 3. Inside
triangular mark 4. Cutting line
Switch action
CAUTION: Before plugging in the tool, always
check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To prevent the switch trigger from being accidentally
pulled,alock-obuttonisprovided.
Tostartthetool,pushinthelock-obuttonandpullthe
switch trigger.
Release the switch trigger to stop.
►Fig.10: 1.Lock-obutton2. Switch trigger
Speed adjusting dial
CAUTION: The speed adjusting dial is not for
using low speed rated blades but for obtaining a
speed which is suitable to material of workpiece.
Use only blades which are rated for at least the maxi-
mum no load speed stated in the SPECIFICATIONS.
CAUTION:Thespeedadjustingdialcanbe
turned only as far as 6 and back to 1. Do not force it
past 6 or 1, or the speed adjusting function may
no longer work.
Thetoolspeedcanbeadjustedbyturningtheadjusting
dial. Higher speed is obtained when the dial is turned in
the direction of number 6; lower speed is obtained when
it is turned in the direction of number 1.
Refer to the table to select the proper speed for the
workpiece to be cut. However, the appropriate speed
maydierwiththetypeorthicknessoftheworkpiece.In
general, higher speeds will allow you to cut workpieces
faster but the service life of the blade will be reduced.
Number min
-1
1 2,200
2 2,700
3 3,800
4 4,900
5 6,000
6 6,400
►Fig.11: 1.Speedadjustingdial
Guide plate
For aligning the guide rail (optional accessory) with the
cutting line, use the guide plate.
►Fig.12: 1. Guide plate 2. Plate edge 3. Cutting line
1. Set the guide plate onto the guide rail near from
the cutting start point. The plate edge represents the
center of the groove cutter blade. Align the plate edge
with the cutting line.
2. Then, set again the guide plate on the guide rail
near the cutting end point. And align the plate edge with
the cutting line again.
Bekijk gratis de handleiding van Makita CA5000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | CA5000 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9333 MB |
