Handleiding
Je bekijkt pagina 5 van 20
IMPORTANT SAFETY INSTRUCTIONS
Be sure the s adequate for the model you have
chosen. This information can be found on the serial plate, which
is located on the side of the cabinet and behind the grille.
Be sure the air conditioner is properly grounded. To minimize
shock and fire hazards, proper grounding is important. The power
cord is equipped with a three-prong grounding plug for protection
against shock hazards.
Your air conditioner must be used in a properly grounded wall
receptacle. If the wall receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or circuit breaker,
have a qualified electrician install the proper receptacle.
Ensure the receptacle is accessible after the unit installation.
Do not run air conditioner without side protective cover in place.
This could result in mechanical damage within the air conditioner.
Do not use an extension cord or an adapter plug with unit.
WARNING
For your safety
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
fire hazard or electric shock, do not use an extension cord or an
adaptor plug. Do not remove any prong from the power cord.
WARNING
Electrical Information
NOTE For some models, the power
cord ir conditioner
contains a current detection device
designed to reduce the risk of fire.
Please refer to the section ‘Operation
of Current Detection Device’ for details.
In the event that the power cord is
damaged and cannot be repaired, it
must be replaced with a replacement
from the Product Manufacturer.
Do not, under any
circumstances, cut,
remove, or bypass
the grounding prong.
Power cord
with 3-prong grounding plug
and current detection device
(Applicable only
to certain
units with current
detection device
)
The power cord contains a current detection function that senses damage to the power cord. To test your power
cord, do the following:
1. Plug
in the
Air Con
ditioner
.
2. The
power
supply
cord wi
ll have
TWO b
uttons o
n the pl
ug head
. Press
the TE
ST bu
tton yo
u will no
tice a
click
as the R
ESET
button
pops ou
t.
3. Pres
s the R
ESET
button,
again y
ou will n
otice a
click as
the but
ton eng
ages.
4. The
power
supply
cord is
now su
pplying
electric
ity to th
e unit. (
On som
e produ
cts this
is also
a ligh
t on the
plug he
ad.)
NOTES
:
Do n
ot use t
his devi
ce to tu
rn the u
nit on o
r off.
A
lways make sure the RESET BUTTON IS PUSHED IN for correct operation.
power cord must be replaced if it fails reset when either the TEST button is pushed, or it cannot be
If power cord is damaged and cannot be repaired, it MUST be replaced with a replacement from the
product manufacturer.
4
Note: Performance may be reduced outside of these operating temperature ranges.
NOTE:This air conditioner is designed to be operated under the following conditions:
Cooling operation
Outdoor temp:
18-43°C/64-109°F (18-52°C/64-125°F for special tropical models)
Indoor temp:
17-32
°C
/62-90
°F
for this a
To avoid
power requirement i
The power cord contains a current detection function that senses damage to the power cord. To test your power
power cord must be replaced if it fails to reset when either the TEST butt
The power cord must be replaced if it fails to reset when either the TEST button is pushed or it
cannot be reset.
indicated by
Operation of Current Detection Device
Bekijk gratis de handleiding van Magnavox MG-06CR3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Magnavox |
| Model | MG-06CR3 |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 3919 MB |
