Maginon OSS-2 handleiding
Handleiding
Je bekijkt pagina 2 van 2
131211
14
987 10
10
OPERATING THE MACHINE
WARNING! RISK OF DAMAGE!
» Notice the maximum shredding capacity: do not exceed 4 sheets per shredding cycle.
» For plastic cards, do not exceed one card per shredding cycle.
» Shredding time should not exceed 3 minutes, as this may cause motor overheating.
» If the machine runs continuously for an extended period, it may automatically pause due to motor overheating. After
cooling for 20–40 minutes, it will resume operation.
NOTICE!
» To ensure proper waste separation, shred plastic cards only when the container is free of paper, and shred paper only
when no credit card remnants are in the container.
» Regularly empty the container to prevent paper or credit card remnants from being pulled back into the cutting
mechanism.
Function Description
Green light Power
Red light Overheat and jammed paper
AUTO Automatic shredding with detection sensor
OFF Turn off the device
FWD Continuously feed paper into the shredding inlet
REV Reverse the paper out of the inlet
1. Connect the power plug to the socket.
2. Set the slide switch
to the “AUTO” position. The power LED will light up green, indicating that the machine is in
standby mode. The detection sensor will activate automatically when paper is inserted.
3. Before inserting the paper, ensure there are no paper clips attached to the paper or card.
4. Insert the paper to be shredded into the center of the inlet
.
5. The device will automatically turn on and feed the paper.
Jammed paper
• In case of a paper jam caused by shredding too much paper, the overheat LED
will light up red.
• To clear a paper or card jam, immediately slide the switch
to the 'REV' position to reverse and eject the stuck
material from the inlet .
• Then, switch to the 'FWD' position to remove any remaining small paper strips.
WARNING! RISK OF DAMAGE AND INJURY!
» Do not insert the fi nger or any objects to clear the jammed paper in the inlet while the device is operating or after turn
it off , this may cause the damage and injury.
Strip dimensions: 4 x 32 mm
Nominal operating time: 3 min
Nominal idle time: 40 min
Noise level: 72 dB
Automatic start / stop function: yes
Energy Consumption "Off " mode: 0.1 W
Energy Consumption "Standby" mode: <0.8 W
Network Connection: No
Design and technical specifications are subject to change without notice.
17
NOTES ON AUSTRALIAN DECLARATION OF CONFORMITY
The manufacturer hereby declares that the RCM marking was applied to the product in accordance
with the basic requirement and other relevant provisions of the Australian directives.
18
DISPOSE OF PACKAGING
Box
Carton
Seal
Sort and dispose of the packaging accordingly. Place cardboard and cartons with paper waste, and foils in the recyclable
materials collection.
18.1
DISPOSE OF THE PRODUCT
Dispose of the product in accordance with the disposal regulations and laws applicable in your country.
19
WARRANTY
19.1
WARRANTY CERTIFICATE
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/TO KEEP UP-TO-DATE WITH
IMPORTANT PRODUCT INFORMATION
Congratulations! You have made an excellent choice of this quality product. Our commitment to quality also includes our
service. Should you, contrary to expectations, experience defects due to manufacturing faults, ALDI will provide you with a
warranty against defects as follows:
The product is guaranteed to be free from defects in workmanship and parts for a period of 3 years (dependant on product)
from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion.
1
Lid
5
Power LED / Overheat LED
2
Container
6
Slide switch (FWD, AUTO, OFF, REV)
3
Viewing window
7
Inlet
4
Carrying handle
8
Caution symbols (see chapter "Explanation of
symbol")
8
SETTING UP AND PLACEMENT
WARNING! RISK OF DAMAGE AND INJURY!
» Improper or negligent handling of the product can lead to damage of the product and injuries.
− The power cord must be disconnected from the power supply during assembly.
− The cutting mechanism in the lid has sharp edges. Proceed with great caution when setting it up.
– Hold and move the product securely at the bottom of the container to prevent it from falling.
1. Place the device parts on a fl at, stable table.
2. Assemble the lid
onto the container .
3. Before connecting the power plug to the socket, ensure that the operating voltage matches the supply voltage.
9
USAGE
WARNING! RISK OF INJURY AND DAMAGE!
» Do not put your fi ngers into the inlet while the machine is operating.
» Do not insert unsuitable material into the inlet (see below table). The cutting mechanism can be damaged.
Suitable Material Unsuitable Material
− Paper (maximum 4 sheets) (plain,
printed, or written documents)
− Thin cardboard (such as greeting cards
or paperboard packaging)
− Credit cards or plastic cards (one card
for a shredding time).
− Metal objects ( paper clips, binder clips, coins)
− Thick plastic (Thick plastic cards, laminated sheets, ID badges)
− Adhesive materials (sticky notes, labels, tape, glue-covered paper)
− Cardboard (thick or corrugated cardboard can jam the blades)
− Fabric or textiles (ribbons, cloth, or synthetic materials)
− Wet or damp paper (can cause clogging and rusting)
− Thermal paper with coated surface (can create residue)
− CDs/DVDs
− Hardcover book pages (too thick and dense)
− Excessive paper at once, overloading can strain the motor and damage
the inlet.
Problem Possible Causes Solution
The device does not start when
feeding paper or stops feeding
during operation.
The paper was fed at an angle,
preventing the activation of the
detection sensor.
Insert the paper straight into the inlet in
a vertical position.
The paper is too thin, too soft, or too
crumpled to reliably activate the
detection sensor.
– Set the switch to 'REV' to remove the
jammed paper.
– Insert only paper suitable for the
shredder.
Shredded paper has blocked the
sensor.
Insert the next paper after the previous
one is shredded.
The device does not turn on. − Damaged power cord or device
− The electric circuit is damaged.
− Check the power cord and power
supply for any signs of damage or
leakage.
− If found, contact customer service.
The machine keeps running after
shredding.
− Full container blocks shredded
paper from falling, leaving it in
the blades.
− The detection sensor is damaged.
− Slide the switch to the "OFF"
position and empty the container.
− If the issue persists, contact
customer service.
16
TECHNICAL SPECIFICATION
Model: EDS-2
Mains voltage: 220 – 240 V~, 50 Hz
Power consumption: 1.0 A
Visible Cable length: approx. 120 cm
Protection class: II
Safety class: P-4 (according to DIN 66399)
Weight: approx. 2.3 kg
Dimensions (W × D × H): approx. 152 x 300 x 256 mm
Working width: 220 mm (DIN A4)
Cutting type: Cross cut
Cutting speed: approx. 2.50 m/min
Container volume: approx. 8 L
Max. Cutting capacity per cycle: 4 sheets of 80 g/m²
» Do not slide to “REV” if the container is full, otherwise, the shredded paper strips inside container might be reversed
into the blades, causing jams.
6. After fi nishing shredding, the machine will automatically stop and enter standby mode.
7. When not in use, slide the switch
to the "OFF" position to shut down the device. The power LED will turn off .
8. Unplug the device before cleaning or disposing of the shredded paper.
10.1
STANDBY MODE AND OFF MODE
Standby Mode:
• Slide the switch
to the “AUTO” position. The green power LED will illuminate, indicating that the machine has
entered standby mode and is ready for use.
• After each shredding cycle is complete, the machine will automatically stop and immediately switch to standby mode.
O ff M ode:
• When not in use, slide the switch
to the "OFF" position to shut down the device. The power LED will turn off , and
unplug the power cord. The device consumes no power when in Off mode.
11
SHREDDING CARDS
1. Turn the short side of the plastic card toward the center of the inlet and insert only one card per shredding cycle.
2. The device will automatically turn on and feed the plastic card.
NOTICE!
» To enable proper waste separation, only shred credit cards when there is no paper in the container.
12
EMPTYING THE CONTAINER
WARNING! RISK OF INJURY!
» Always disconnect the device from power when it is unattended and before assembling, disassembling, or cleaning it.
» Be cautious when handling sharp edges, emptying the container, and cleaning.
NOTICE!
» Regularly empty the container to prevent paper or credit card remnants from being pulled back into the cutting
mechanism.
» To enable proper waste separation, only shred credit cards when there is no paper in the container and only shred
paper when there are no remnants of shredded credit cards in the container.
1. Set the slide switch
to the "OFF" position. The power LED will turn off .
2. Disconnect the power plug from the socket.
3. Lift the lid
off the container .
4. Empty the container
.
5. Reassemble the device.
13
CLEANING
WARNING! RISK OF DAMAGE AND INJURY!
» Always unplug the device before cleaning and storage.
The benefi ts conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer
has under the Competition and Consumer Act 2010 and similar state and territory laws. Our goods come with guarantees that
cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
19.2
PROOF OF PURCHASE
This warranty is valid for the original purchase and is not transferable. Please keep your purchase docket, tax invoice or receipt
as the best proof of purchase, and as proof of date on which the purchase was made.
19.3
EXTENT OF WARRANTY
This warranty is limited to defects in workmanship or parts. All defective products or parts will be repaired or replaced. This
warranty does not cover batteries or any other consumable items.
19.4
NORMAL WEAR AND TEAR
This warranty does not cover normal wear and tear to the products or parts.
19.5
EXCLUSIONS
This warranty does not cover:
− Any defects caused by an accident, misuse, abuse, improper installation or operation, lack of reasonable care,
unauthorised modifi cation, loss of parts, tampering or attempted repair by a person not authorised by the distributor.
− Any product that has not been installed, operated or maintained in accordance with the manufacturer’s operating
instructions provided with the product.
− Any product that has been used for purposes other than domestic use.
− Any damage caused by improper power input or improper cable connection.
19.6
TO MAKE A CLAIM
This warranty against defects is provided by:
ALDI Stores, Locked Bag 56, St Marys Delivery Centre, NSW 2760, Phone (02) 9675 9000.
If a defect in the goods appears within 3 years (the identifi ed period on the packaging), you are entitled to claim a warranty,
please contact or send all warranty claims to:
ACR Supply Partners Pty Ltd.50 Old Wallgrove Road, Eastern Creek, NSW 2766, AUSTRALIA
Tel: 1800 130 489 (Mon-Fri 8 am - 6:30 pm AEST)
service-au@protel-service.com
When making a return, please ensure the product is properly packaged so as to ensure that no damage occurs to the product
during transit. Please provide the original or a copy of the proof of purchase. Also please make sure you have included an
explanation of the problem. Please note that the costs of making a warranty claim, including any return postage, will be
covered by the supplier identifi ed above. Please note upon receiving your warranty claim, the supplier will send, via the post
or email, a repair and refurbished goods or parts notice. Please provide your email address and advise the supplier, if you wish
to obtain a repair and refurbished goods or parts notice via email.
» Allow the device cool down before cleaning and storage.
» Do not immerse the device in water or other liquids.
» Ensure no water or other liquids enter the motor and electrical part.
» Be cautious when handling sharp edges, emptying the container, and cleaning.
» Do not use aggressive cleaning agents, brushes with metal or nylon bristles, or sharp or metallic cleaning objects like
knives, hard scrapers, etc. These can damage the surfaces.
1. Set the slide switch
to the "OFF" position. The power LED will go out.
2. Disconnect the power plug from the socket.
3. Regularly remove any residue from the container
and the underside of the lid . Use a suitable tool for this purpose
(e.g., a brush).
4. Use a dry or slightly damp cloth to clean the exterior, then allow all parts to dry thoroughly.
14
STORAGE
NOTICE! RISK OF DAMAGE!
» Always unplug the device before cleaning and storage.
» Allow the device cool down before cleaning and storage.
» Store the device in a clean, dry, frost-free location out of reach of children.
1. Thoroughly clean the device (see the "Cleaning" chapter).
2. Coil the power cord without knotting or bending it.
3. Always store the device parts and accessories together with the device.
4. If possible, package the device in its original packaging.
15
TROUBLESHOOTING
Some disturbances can be caused by minor errors that you can resolve yourself. Follow the instructions in the table below to
troubleshoot.
Problem Possible Causes Solution
• The overheat LED lights up red.
• A paper jam occurs, and the
machine stops operating.
• The motor overheats, or
the device turns off during
operation.
A paper jam occurred because
excessive paper or multiple cards were
fed into the device at once.
1. Slide the switch to 'REV' to eject the
jammed material.
2. Then, switch to 'FWD' to clear any
remaining scraps.
The device was operated beyond the
specifi ed rated operating time of 3
minutes.
1. Turn off the switch and unplug the
device if the motor overheats.
2. Let it cool for 20–40 minutes.
3. After cooling, plug it in and turn
it on.
4. If the power LED is green, the device
is ready.
19.7
WARRANTY DETAILS
The product is guaranteed to be free from defects in workmanship and parts for a period of 3 years from the date of purchase.
Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our
discretion. The benefi ts conferred by this warranty are in addition to all rights and remedies in respect of the product that the
consumer has under the Competition and Consumer Act 2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
19.8
REPAIR AND REFURBISHED GOODS OR PARTS NOTICE
Unfortunately, from time to time, faulty products are manufactured which need to be returned to the Supplier for repair.
Please be aware that if your product is capable of retaining user-generated data (such as fi les stored on a computer hard drive,
telephone numbers stored on a mobile telephone, songs stored on a portable media player, games saved on a games console
or fi les stored on a USB memory stick) during the process of repair, some or all of your stored data may be lost.
We recommend you save this data elsewhere prior to sending the product for repair.
You should also be aware that rather than repairing goods, we may replace them with refurbished goods of the same type or
use refurbished parts in the repair process.
Please be assured though, refurbished parts or replacements are only used where they meet ALDI’s stringent
quality specifi cations.
If at any time you feel your repair is being handled unsatisfactorily, you may escalate your complaint. Please telephone us on
1 800 130 489 or write to us at:
ACR Supply Partners Pty Ltd.50 Old Wallgrove Road, Eastern Creek, NSW 2766, AUSTRALIA
Tel: 1800 130 489 (Mon-Fri 8 am - 6:30 pm AEST)
service-au@protel-service.com
Bekijk gratis de handleiding van Maginon OSS-2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Maginon |
| Model | OSS-2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 868 MB |
