Mackie MainStream handleiding
Handleiding
Je bekijkt pagina 27 van 64
MACKIE MATRIX LIVE STREAMING MIXER SOFTWARE
27
Input Meters – The stereo input meters display the relative level of each input channel. They should remain green
with the occasional bump into the yellow zone. Turn down the volume if the input meter remains consistently yellow.
If the input is too high [overloading], a clip indicator at the top of the meter will illuminate red. If clipping occurs,
reduce the volume.
This only displays the input meter level. The input may be lowered by either () lowering the source
of the input and/or (2) lowering the input fader level (located on the main mixing screen).
Ok friends, let’s swing on over to the upper-right side of the screen now!
X – Clicking on the “X” will close out the Control Mode window and return you to the mixer view.
This is the only way to access the mixer view. The Control Mode screen
cannot be “moved out of the way” to make changes to the mixer view.
Expand/Contract – The Control Mode window may be scaled for a larger
(or smaller) look, how ’bout them apples?! In the lower-right corner
of the screen are several diagonal lines. These may be clicked (and held)
while moving the mouse down and out/right (screen expands) or up
and in/lef (screen shrinks).
Again, regardless of screen size, the Control Mode
screen cannot be “moved out of the way” to make
changes to the mixer view.
Output Meters – The output meters display the output signal level, presented in stereo L/R.
The meters should remain green with the occasional bump into the yellow zone.
If there is too much yellow (or any red clipping), lower the output gain (more below)
until it’s gone and check the input channels, as well.
Output Gain – Located below the output meters is the output gain control. Use it to raise/
lower the output gain by up to ±2 dB. This may be changed one of two ways: () hovering
inside of the output gain circle, then rotating the mouse wheel to change the output gain;
increments will be ± dB, or (2) lef (or right)-click (and hold) the mouse inside of the
output gain circle while also moving the mouse up (increases gain) or down (decreases
gain) by ±0.xx for even more detailed settings!
There is still one thing we haven’t discussed... yet it’s the thing that takes up the most
space on the Control Mode screen. Yes, we’re talking about the M-VOICE knob!
There is a screenshot of the entire EASY Control Mode screen two pages ago. The included
dynamics – EQ, Gate, Compressor, and De-esser – are processed and mixed. Raising or lowering
this knob aects that dynamic audio processing. This knob sets the total amount of the mixed
dynamics for this input/channel (with the parameters of the dynamics set up by... you!)
The range is from 0 (o) to (max).
This may be changed in one of three ways:
() Hovering inside of the M-VOICE circle, then rotating the mouse wheel to change the amount
of dynamics; these increments will be ±0.04 dB.
(2) Lef (or right)-click (and hold) the mouse inside of the M-VOICE circle while also moving
the mouse up (increases dynamics level) or down (decreases dynamics level) by ±0.0 for even
more detailed settings!
(3) Click the mouse on the number below the knob to enter the amount of dynamics you prefer.
Note that anything ≥±0.005 will be rounded up, while anything ≤±0.004 will be rounded down.
Presets – Presets save parameters and may be recalled as needed.
Mackie Matrix comes with a library of factory presets. There are
also user presets. These may be created for each preset type.
The presets pull-down is located at the top-center of the display.
Mouse-click on it to open the pull-down menu that presents the list
of options.
Click-and-hold on a preset – Factory to start with – so it is highlighted
then release to select. Once released, all appropriate parameters
change to match the stored preset. You’ll hear the changes immediately
and should notice visible changes to the settings, as well. From here,
all that’s required is to rotate the giant knob!
We highly suggest that beginners start with this
route until fully comfortable with how to make
changes to the parameters.
The following pages explain in detail how to set up your own personal
parameters for each dynamic within the Easy Control Mode section.
An entire chapter is dedicated to presets. This includes detailed instructions and multiple screenshots every step of the way.
Please check it out on pages 56-6.
Bekijk gratis de handleiding van Mackie MainStream, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Mackie |
| Model | MainStream |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10845 MB |