Handleiding
Je bekijkt pagina 7 van 14
Fig. 5
u
Lift out the bearing pin
Fig. 5 (22)
together with washer
Fig. 5 (23)
and adjustable-height foot
Fig. 5 (24)
.
u
Lift off the stopper
Fig. 5 (21)
.
u
Unscrew
Fig. 5 (26)
the turn hinge
Fig. 5 (25)
.
u
Unscrew
Fig. 5 (29)
the bearing element
Fig. 5 (28)
, transfer
it to the opposite location hole of the turn hinge and screw it
firmly into place.
u
Carefully lift off the cover on the handle side
Fig. 5 (27)
and
transfer it to the opposite side.
u
Screw the turn hinge
Fig. 5 (25)
firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u
Re-insert the stopper
Fig. 5 (21)
into the other hole.
u
Re-insert the bearing pin
Fig. 5 (22)
together with the
washer and adjustable-height foot. In so doing, pay attention
that the locating lug points backwards
4.3.4 Changing the bearing parts
For appliances with height adjustment
Fig. 6
u
Using the accompanying Allen key, unscrew the threaded
pin
Fig. 6 (40)
by about 1 turn.
u
Turn and lift out the bearing pin
Fig. 6 (22)
together with the
washer
Fig. 6 (23)
and adjustable-height foot
Fig. 6 (24)
.
u
Lift out the stopper
Fig. 6 (21)
.
u
Unscrew
Fig. 6 (26)
the turn hinge
Fig. 6 (25)
.
u
Fully unscrew the threaded pin
Fig. 6 (40)
and screw it in on
the opposite side, at the turn hinge, until it is flush outside
with the turn hinge.
u
Unscrew
Fig. 6 (29)
the bearing element
Fig. 6 (28)
transfer it
to the opposite location hole of the turn hinge and screw it
firmly into place.
u
Re-insert the stopper
Fig. 6 (21)
into the other hole.
u
Carefully lift off the cover on the handle side
Fig. 6 (27)
and
transfer it to the opposite side.
u
Screw the turn hinge
Fig. 6 (25)
firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u
Re-insert the bearing pin
Fig. 6 (22)
together with the
washer and adjustable-height foot.
u
Tighten the threaded pin
Fig. 6 (40)
.
4.3.5 Transferring the handle
u
Transfer the spring clamp
Fig. 7 (31)
: Depress the
latch nose and pull the
spring clamp off over it.
u
Slide the spring clamp
into place on the new
hinge side until it clicks
into place.
Fig. 7
Fig. 8
u
Lift the stopper
Fig. 8 (33)
out of the door bearing bush and
transfer it.
u
Dismantle the door handle
Fig. 8 (32)
, stoppers
Fig. 8 (33)
and pressure plates*
Fig. 8 (34)
and transfer to the opposite
side.
u
When fitting the pressure plates on the opposite side, make
sure they snap properly into place.*
4.3.6 Fitting the door
u
Place the door from above onto the lower bearing pin
Fig. 6 (22)
.
u
Close the door.
u
Insert the upper turn hinge
Fig. 4 (12)
in the door on the new
hinge side.
u
Screw the upper turn hinge
Fig. 4 (12)
firmly into place (with
4 Nm)(2x Torx® 25)
Fig. 4 (13)
. Possibly make preliminary
holes with a bradawl or use a cordless screwdriver.
u
Snap the cover
Fig. 4 (10)
and cover
Fig. 4 (11)
into place at
the opposite side.
4.3.7 Aligning the door
u
Align the door to the appliance housing by way of the two
oblong holes in the bottom turn hinge
Fig. 6 (25)
. To do so,
unscrew the middle screw.
Putting into operation
* Depending on model and options 7
Bekijk gratis de handleiding van Liebherr SKes 4210 LH, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Liebherr |
| Model | SKes 4210 LH |
| Categorie | Koelkast |
| Taal | Nederlands |
| Grootte | 2198 MB |
