Handleiding
Je bekijkt pagina 11 van 22
u
Refitting the closing dampers: Screw in the ball studs (1),
tighten the bracket (2) and hang the closing dampers in
the ball studs.*
u
Check all screws and retighten if necessary.
Fig.22
u
Reassemble the bottom and centre cover. Only replace
the remaining covers after installing the appliance back
into the cabinet.
15 Connecting the appliance to the
water supply*
Make sure that the following requirements are fulfilled:
q
The dimensions for the water supply connection are
known and complied with. (see 7.1 Dimensions for the
water connection)
q
The correct water pressure is maintained. (see 7.1 Dimen‐
sions for the water connection)
q
Water is supplied to the appliance via a cold water
pipe which can withstand the operating pressure and is
connected to the drinking water supply.
q
All equipment and devices used to supply water must
comply with the regulations in force in the respective
country.
q
The rear of appliance is accessible so that you can
connect the appliance to the drinking water supply.
q
The supplied hose is used. Old hoses have been disposed
of.
q
The hose connector contains a filter with a seal.
q
There is a tap between the hose line and the domestic
water connection so that you can turn off the water
supply if necessary.
q
The tap is not directly behind the appliance and is easily
accessible. This way, you can push the appliance as far
as possible into the cabinet recess and can quickly turn
off the tap if necessary.
WARNING
Risk of electric shock from water!
u
Before connecting to the water pipe: Disconnect the
appliance from the mains.
u
Before connecting to water supply lines: Shut off the
water supply.
u
Make sure that only qualified personnel connect the
device to the drinking water supply.
WARNING
Risk of poisoning due to contaminated water!
u
Only connect to the drinking water supply.
15.1 Connecting the hose
Fig.23
Fig.23
(1)
Nut (4) Straight hose end
(2) Angled hose end (5) Tap
(3) Bracket (6) Solenoid valve: The sole‐
noid valve is at the
bottom on the back of
the appliance. It has an
R3/4 connecting thread.
NOTICE
Risk of damage from incorrect installation!
u
Do not damage or kink the hose.
u
Do not damage or kink the hose during installation in the
cabinet recess.
Connecting the hose to the appliance:
u
Position and hold the angled hose end Fig.23(2) horizon‐
tally on the bracket Fig.23(3).
u
Screw on the nut Fig. 23 (1) on by hand until it is firmly in
place.
w
The hose is connected to the appliance.
Connecting the hose to the tap:
u
Connect the straight hose end Fig. 23 (4) to the tap
Fig.23(5).
w
The hose is connected to the tap.
15.2 Checking the water system
Before you completely install the appliance in the cabinet
recess, Liebherr recommends checking the water system for
leaks.
u
Put in the InfinitySpring water tank. (see 18 Water tank*)
*
u
Put in the InfinitySpring water filter. (see 19 Water filter*)
*
u
Slowly turn on the tap.
u
Check the hose, water feed and connections for leaks.
Connecting the appliance to the water supply*
* Depending on model and options 11
Bekijk gratis de handleiding van Liebherr IRBci 5170 Peak, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Liebherr |
| Model | IRBci 5170 Peak |
| Categorie | Koelkast |
| Taal | Nederlands |
| Grootte | 6277 MB |
Caratteristiche Prodotto
| Apparaatplaatsing | Ingebouwd |
| Soort bediening | Touch |
| Kleur van het product | Wit |
| Deurscharnieren | Rechts |
| Ingebouwd display | Ja |
