Lavor DMX-R 80 handleiding
Handleiding
Je bekijkt pagina 12 van 32
CONNECTING THE UNIT TO THE ELECTRICAL CUR-
RENT
ATTENTION:
•
Make sure the electrical specications on the
technical data label of the unit correspond to
those of the electrical network.
•
Make sure the direction of rotation of the tur-
bine is correct. This can be veried by check-
ing if there is a vacuum or air depression at the
vacuum inlet. If not, the direction of rotation
can be corrected by reversing the polarity of
the unit’s plug.
TURNING ON THE UNIT
•
The switch must be in the “0” or “o” position.
•
Attach the plug to the electrical current socket.
•
Turn on the unit by pressing the switch in the “I”
or “on” position.
•
Make sure the direction of rotation of the tur-
bine is correct by verifying air depression at the
vacuum inlet as described above.
TO EMPTY THE RECOVERY TANK
•
Turn o the unit (switch in the “0” position.
•
Disconnect the plug from the electrical current
socket.
•
The tank is kept in position thanks to a magnet-
ic system, grip the handles and lever to rotate
and release the tank, for assembly repeat the
reverse operation
ATTENTION! Never leave waste material of any
kind in the tank for long periods of time.
TO CLEAN THE FILTER
•
Make sure the unit is turned o (switch in the
“0” position).
•
The lter can be cleaned using the special lter-
cleaning handle on the lid or on the side of the
upper tank.
TO REPLACE THE FILTER
•
Make sure the unit is turned o (switch in the
“0” position).
•
Disconnect the plug from the electrical current
socket.
•
Unlatch the lid, raise it and remove the lter.
•
Replace the lter with a new one, tighten the
same original xture band around the ring, and
replace the lter assembly back into its original
position on the tank
•
Close the latches on the lid.
WARNING
ATTENTION!
•
Before starting, read carefully the instructions
manual and follow these safety instructions.
•
The danger and of warning signs on the ma-
chine provide important information for the
safe operation of the unit.
•
In addition to the information in the operat-
ing instructions, all the general laws of safety
and of the prevention of accidents must be fol-
lowed.
•
The performance of the turbine can vary by
15% based on the temperature and humidity
of the air.
•
The safety valves are calibrated according to
the amperage of the turbine.
ATTENTION! The appliance is not intended for
use by persons (including children) with redu
-
ced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
ATTENTION! Children should be supervised to
ensure that they do not play with the appliance.
ELECTRICAL CONNECTIONS
•
The voltage indicated on the rating plate must
correspond to the voltage of the electric source.
•
Safety class I – The units may only be con-
nected to properly earthed (grounded) electric
sources.
The appliance’s electrical connection must
comply with the IEC 60364-1 standard.
•
IMPORTANT:
Before connecting the appliance, make sure
that the nameplate data are the same as those
of the electrical mains and that the socket is
protected by a dierential security breaker with
tripping sensitivity below 0.03 A - 30 ms.
If the appliance’s plug is not compatible with
Translation of the original instructions
EN
12
Bekijk gratis de handleiding van Lavor DMX-R 80, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lavor |
| Model | DMX-R 80 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 4634 MB |
