Lasko S18670 handleiding
Handleiding
Je bekijkt pagina 3 van 6
MODELO S18670
FUNCIONAMIENTO
Este Ventilador puede hacerse funcionar mediante los Controles Manuales ubicados en la parte superior de la
unidad (como se muestra en la Figura 10) o con el Control Remoto (se muestra en la Figura 13).
1. Conecte el cable eléctrico a un tomacorriente de 120 V~.
2. Conecte la energía eléctrica a su ventilador pulsando el Botón Alimentación ( ).
3. VELOCIDAD DEL VENTILADOR: Ahora puede ajustar la velocidad del ventilador presionando el botón de
velocidad del ventilador ( ).
4. OSCILACION: Empuje la perilla ubicada en la parte superior de la caja del motor para hacer que la cabeza del Ventilador
se mueva de un lugar hacia otro. (Figuras 11 y 12)
5. Después de apagar el Ventilador, desconecte la unidad del tomacorriente eléctrico.
Rev. A 7/17
10
2084905
Rev. A 7/17
3
2084905
1. Take pipe assembly out of carton as shown. (Figure 1)
2. Loosen Height Adjustment Nut turning counter clockwise. (Figure 2)
3. Raise Extension Pipe. (Figure 3)
4. Tighten Height Adjustment Nut turning clockwise. (Figure 4)
STEP 1: PIPE ASSEMBLY
STEP 2: STAND ASSEMBLY
PLACE BASE FLAT ON FLOOR
1. With a twisting motion, insert the end of the large diameter
pipe into hole in Base. (Figure 5) Turning pipe while pushing
will assure pipe is fully seated in Base.
2. For Height Adjustment:
a) Loosen Height Adjustment Nut.
b) Raise or lower Extension Pipe to desired height.
c) Tighten Height Adjustment Nut.
1. Place Head Assembly with
Collar onto Extension Pipe.
(Figure 6)
2. Holding Extension Pipe
firmly, twist Head Assembly
downward until seated on
Extension Pipe.
1. Tilt Head Assembly back. Put Rear Grill on Head Assembly.
(Figure 7)
2. Align tab of Plastic Rear Grill with groove on top of front
Head Assembly.
STEP 4: BLADE & GRILL ASSEMBLY
3. Fully seat Rear Grill and secure with Plastic Nut turning Clock-
wise. Slide Blade onto Motor Shaft. (Figure 8) Align Groove on
blade hub with Pin on motor shaft. (Figure 8A)
4. To secure Blade, screw Fan Spinner onto Shaft
Counter Clockwise until tight on Blade hub.
STEP 3: HEAD ASSEMBLY
Head
Assembly
Collar
Extension
Pipe
Figure 6
Botón
Alimentación
Figura 10
Figure 2 Figure 4
Figure 3
Figure 1
Height
Adjustment
Nut
Extension
Pipe
Rear
Grill
Figure 7
Figure 8A
Pin
Groove
Hacia Arriba: Estacionario
Hacia Adelante: Oscilar
Figura 11
Figura 12
Botón
Velocidad del
Ventilador
Figure 5
Extension Pipe
Height
Adjustment Nut
Base
5. With fan head in upright position, align Ornament of Front Grill
so it is horizontal and right side up. By starting with the top of
the grill and working down, insert Snaps on Rear Grill through
Slots in Front Grill (Figure 9).
Do Not take pipe apart. Should pipes become separated, insert
pipe A into pipe B.
A
B
Head
Assembly
Larger
Pipe
Rear Grill
Figure 8
Fan
Spinner
Plastic Nut
Blade
Adorno
Ranuras
Trabas
Parrilla
Trasera
Parrilla
Delantera
Figura 9
Bekijk gratis de handleiding van Lasko S18670, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lasko |
| Model | S18670 |
| Categorie | Ventilator |
| Taal | Nederlands |
| Grootte | 1528 MB |
Caratteristiche Prodotto
| Kleur van het product | Zwart |
| Gewicht | 5556 g |
| Breedte | 521 mm |
| Diepte | 521 mm |
| Hoogte | 1359 mm |
